100122 PROMAX Provax Black Knob

100123 PROMAX Provax Blue Knob

100124 PROMAX Provax Red Knob

Inlet Block Manifold shim plate installs directly over the manifold, preventing the valve stems from backing out after installation in the unit. This plate also prevents unwanted removal or accedental removal or service of stems during use. If you are replacing the manifold on your unit we strongly suggest installing this as well for safety reasons.

1/4" Flare Filter for ProMax and MiniMax Units Designed to protect recovery systems from debris and deposits that would normally harm your unit. Large filter capacity provides long life. All steel construction with enamel finish resists corrosion and rusting.

100345 PROMAX Hose, Blue, 4" Long

50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

Inlet Block / Manifold Assembly includes black machined block, valves and new knobs. (Caution! Do turn knobs from there original position before installing or they will lose there indexing and improper flow will result)

CP1001 PROMAX Compressor Mount (Rg5xxx)

CP1304 PROMAX Piston

Offset Motor Pump Coupler. Includes coupling, set screw, cap screws, dowel pin.

CP1320 PROMAX Compressor (Replaces CP1300 Except RG3305)

CP1321 PROMAX Connecting Rod (CP1320) less any hardware, you will need bearings, piston, screw, bushings and wrist pin to complete the assembly.

CP1322 PROMAX Crank Shaft (CP1320)

Valve Plate, no valves or springs. When purchasing this it is customary to purchase the rebuild kit as well, found here.

CRXTOSP1 Tank Overfill Protection Cable Shorting Plug allows the user to override the tank float safety device on most recovery units using a 3 pin brad Harrison cable. Screws in place at the cable end allowing the unit to start. (Always use a scale for accuracy when using this device) 30 & 50 pound tanks should never be filled to a level beyond 80% of tank capacity.

EL1309 PROMAX Momentary Switch

EL1310 PROMAX On/Off Switch

EL1412 PROMAX Capacitor

EL1420 PROMAX Sensor Cord

EL1500 PROMAX Relay DPDT 120VAC 30A

1/2 Hp Ac Motor (110v) with starting relay (not available as a seperate item)

FLCK-1 PROMAX Filter Conversion Kit (Replaces MF1275 Swivel). Allows for use of common Filter Drier. Includes: 100343 Filter Drier, 100345 Blue 4" Hose, Flare Adapter Fitting, 1/4 seal cap with retaining strap.

800psi Gauge (Red), 1/8" MPT Bottom Tap Fitting, 0 To 800 PSI 800 PSI Max Pressure Scale, PSI/BAR pressure readings, R-410a PT Scale

GA1000 PROMAX Gauge Lens

500psi Gauge (Blue), 1/8" MPT Bottom Tap Fitting, -30"HG To 250 PSI 500 PSI Max Compound Scale, PSI/BAR pressure readings, R-410a PT Scale

This module plugs directly into the wire harness of your PROMAX Recovery unit through a plug already installed on your machine. This allows you to recover unattended with out the danger of tank overfill or the need to have a scale present to weigh the tank.

This PROMAX piston seal replacement kit is to be used on the old style (round cylinder) and new style (rectangle Cylinder) compressors on RG54xx series, MiniMax Series and PROVAC Compressors.

PROMAX Valve Replacement Kit is to be used on the old style (round cylinder) and new style (rectangle Cylinder) compressors on RG5410 series, MiniMax Series and PROVAC Compressors. Kit includes all necessary parts to rebuild damaged valves and seals.

This PROMAX piston compressor rebuild kit includes all parts needed to rebuild the new style (Rectangle Cylinder Only) compressors on RG54XX series, MiniMax Series and PROVAC Compressors. Kit includes all necessary parts to rebuild the piston "SLYD" Rings, Square piston seal and cylinder seat seals, as well as all necessary parts to rebuild damaged valves and seals and finally the bearings and shaft seal. This Kit does not include the actual valve plate, we suggest the purchase of the valve plate itself here. This kit will not repair round cylinder compressors.

Shaft Seal Replacement Kit for CP1320 Compressor. Includes bearings, seals and o-rings and illustrated instructions.

NB4205 PROMAX Connecting Rod Set Screw

PROMAX WRIST PIN 1/4" DIA X 3/4" For Connecting Rod (CP1320)

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

SB4000 PROMAX Connecting Rod Bronze Bushing 1/4" ID