Power Cord

This Knob is for selector switches on SE Series chargers only, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

0099000066 Schumacher Battery Charger Axle 3/8 Dia.15-3/8" Long.

Mechanically controls charging in timed Mode with manual hold mode. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" spade terminals.

0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

0099000120 Schumacher Wheel 7" Plastic For 3/8 Axle

This Knob is for selector switches with a 3/4 Shaft only, there are separate knobs for timers with a half shaft. Please check your part numbers carefully.

6 Position Rotary Selector Switch (5 Terminals). Older Units used this switch and can be identified by the difference in cabinet mounting, this switch uses a threaded collar with jam nut to mount to case.

0499000050 Schumacher Rocker Switch 2 Position Switch 3 Terminal On-On

1199004366 Schumacher "U" Bracket For 3/8" Axle

1199005112 Schumacher Foot, Metal, no hardware included. For 8" Wheeled units.

2100800011 Schumacher Pop Rivet 3/16" X 5/16" Long

Axle End Cap Fits .375 (3/8") Diameter Axle, Sold as a Pair, Can be used on any 3/8" Axle to secure wheels.

12volt DC Fan Speed Controller (Three Wire)

Heatsink Rectifier Assembly, requires no soldering to install. Used on newer style units. Heavy Duty design for more reliability. 1/4" spade terminal leads make installation a snap. This unit does not include insulators, bolts, nuts or any other hardware.

Fan Motor provides cooling for the unit. 80mm X 80mm X 25mm 12volt DC quiet design keeps noise to a minimum. May require the purchase of a 2299001542 Schumacher 12volt DC Fan Speed Controller.

12volt DC Fan Speed Controller (Two Wire New Style)

2299002762 Schumacher Fan Speed Control (Single Fan) For Rivit See 2100800011

SPDT Switch 16 amp Rating Snap-in mount no tools required to install, 1/4 Spade terminals.

3199100028A 75 Amp 400 Volt Positive Diode (Anode On Lead). Press in diode, used in a wide array of applications. Once installed in the heat-sink these may require soldering to install onto transformer taps.
Use caution when replacing diodes always verify polarity or damage to equipment or self may result. Century Tool & Equipment assumes no responsibility for loss, damage or personal injury due to the miss-application of any electrical component. Purchase of this item agrees to said statement. This item should only be installed by a qualified and experienced electrician.

3599000662 Schumacher Battery Charger Handle Round Black Steel. Replaces handle part number 3599000136.

Output Cable And Clamp, Black Negative, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 82" long with square strain relief on cable.

Output Cable And Clamp, Black Negative, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 83" long with square strain relief on cable.

Output Cable And Clamp, Red Positive, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 88" long with square strain relief on cable.

3999000108 Schumacher Circuit Breaker 32 Volt DC 100 Amp. When ordering, it may be necessary to purchase a pair of the 5199000406 screws if replacing and older circuit breaker for retrofit.

Fan Motor provides cooling for the unit. 80mm x 80mm x 25mm 12volt DC Quiet design keeps noise to a minimum. May require the purchase of a 2299001542 Schumacher 12volt DC Fan Speed Controller. Note plug end to determine correct fit. *Please note: If replacing the 2299001565, you may have to swap plug ends from your old fan to make the new fan work. See 169116-001 for connectors

5100000005 Screw M3 X 5.5 For Original Timer

5399100132 Schumacher Ammeter Horizontal 0-50 AMP features easy snap-in installation, no tools required. Black Charge Rate face. 0-50 Amp range with start. Wire through induction pick-up for greater accuracy.

Horizontal Panel Mount Volt Meter. 6-12 Volt Range, Battery Percent Of Charge Scale and Alternator Test Scale. Bad - Weak - Good. 4 Point Snap In Mount. 1/4" Spade Terminals. Circuit Board Installed. Can be used for older units as a universal replacement. Wiring: P1 -Common to breaker. P2 - To 6 Volt terminal on Switch. P3 - To 12 Volt terminal on Switch.

6094K89 Knob For Battery Charger Selector Switches & Timers. This Knob is for selector switches and timers, designed with 1/4" ID and a set screw for locking onto shaft. Suitable for all 1/4" shaft switches. Replaces Schumacher 0099000045 & 0099000096.

TJ1-120MB Universal Mechanical 2 Hour Timer With Finish Bell. Mechanically controls charging in timed Mode, has "Hold" for manual un-timed charging. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" Quick Disconnect terminals. Includes mounting screws. Replaces many older mechanical timers.