112364 Robinair O-Ring For R-134a Quick Seal Fittings (Each). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

116420 Robinair TEE 1/8 MPT X 1/8 FPT X 1/8 FPT

36" of 1/8" Black Nylon Tube, used to connect low-side and high-side gauge to manifold block and connect oil drain block to drain.

121829 Robinair 1/4-20 3/4" Pan Torx Screw (Each)

122745 Robinair Light Hole Cover For Sidewinder Top

Power Cord 15' Euro Colors Power Cord 15' Supplies main power to the unit.

123785 Robinair Discharge Oil Coalescing Filter O-Ring

123786 Robinair Discharge Oil Filter Canister O-Ring

123787 Robinair Discharge Oil Coalescing Element separates oil from vapors in the discharge gas stream so it can be returned back to the compressor. This filter can become plugged when a compressor fails from a burn out or overheating due to waxes normally found in refrigerants.

Keep recovery and recycling units operating at peak efficiency with a convenient maintenance kit. Contains one quick change filter-drier to be used on either R-12 or R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil.  Designed for newer units manufactured after 1998.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

Robinair 10" Heavy Duty Foam Filled Pneumatic wheel with bearings for Sidewinder style Cart units. Replaces 19823. No more flat tires. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation and long life. Additional hardware for the unit is a Cotter Pin 1/8" Diameter X 1" Long & Flat Washer 1/2" I.D.

Robinair Calibration Verification Weight (1.18lbs.). Easily maintain your units accuracy with this handy calibration weight. Ships with each new unit. This is a factory part, calibrated for accuracy.

Low Side Tank Adapter. 1/2" ACME Female X Lowside Spud used for tank fill and maintenance procedures. 1/2" ACME Female x Low-Side R-134a Coupler

Discontinued See 17492

Oil Drain Bottle For Robinair Sidewinder Cabinet Style Recovery Machines

17773 Robinair O-Ring For R-134a Quick Seal Fittings (2 Pack). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

QUICK SEAL O-Ring Set (6 Pack), O-Rings made of durable silicone rubber for resilience and long life.  fits all 1/4" Flare Quickseal Hose Ends.

Lowside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

Highside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

18192 Robinair High/Low Side Service Couplers 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

19056 Robinair Heavy Duty Refrigerant Tank Strap With Buckle

19740 Source Tank Filter For 134A units. Protect your investment from debris and harmful elements from tank manufacturing processes. Metal debris can foul solenoids causing unnecessary repairs and equipment failures. Install this filter on the hose end of your tank add hose to protect your machine. 100 mesh screen is replaceable or cleanable. 1/2" Female ACME X 1/2" Male ACME fittings Installs inline of tank fill hose.

Robinair 10" Heavy Duty Foam Filled Pneumatic wheel for Sidewinder style Cart units. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation and long life.

Combines simple operation with superior accuracy. The Cool-Tech 34288 recovers, recycles, evacuates, leak tests, and recharges R-134a quickly and accurately. Semi-automatic operation means less attention is needed! Features include, Automatic Recovery, automatic air purge, automatic oil drain, refrigerant charging, new display, vacuum function, refrigerant management system.  (Brand New Open Box Display Unit, Full factory warranty)

Set of Red/Blue 9’ Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant.

The 34724 Robinair filter drier has been specifically formulated to trap acid and particulates and is formulated to remove water from the refrigerant. DO NOT accept look alike or knock off filters. You must change the filter-drier to assure adequate moisture and contaminant removal. Typically, you can recycle up to 300 pounds (136 kilograms) of R-134a or 600 pounds (272 kilograms) of refrigerant between filter changes (depending on your model). To help you know when you’ve reached that point, the unit displays the warning message prompting you to change the filter drier.

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

518638 Robinair 15 Amp Magnetic Circuit Breaker provides protection of main electrical input. Single Pole 15 Amps 125-250 AC. Mounts Via Snap In Bezel. Terminal Connection 0.250 Spade terminals.

518658 Robinair Knob, Low Side Valve Blue (Kantleak Style Valves)

518659 Robinair Knob, High Side Valve Red (Kantleak Style Valves)

519605 Robinair Air Exhaust Muffler

522975 Robinair 116" High Side Enviro-Guard Hose Coupler Set R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure. Fittings are 7/16" Flare x 14MM Hose for Automotive R-134a.

522976 Robinair 116" Low Side System Hose with coupler R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure. Fittings are 7/16" Flare x 14MM Hose for Automotive R-134a.

Robinair Cabinet Top Rear Pocket Panel keeps documents and user manual handy for reference. For 34288 / 34788 refrigerant recovery units.

Tank Temperature Probe senses refrigerant temperature for purge process.

Robinair Calibration Verification Weight for 34988 34788 and 34288 units. Easily maintain your units accuracy with this handy calibration weight. Ships with each new unit. This is a factory part, calibrated for accuracy.

541384 Robinair 9 Foot Enviro-Guard High Side Hose For 34788 34288 34134Z Units. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure. Fittings are 7/16" Flare x 14MM Hose for Automotive R-134a.

541385 Robinair 9 Foot Enviro-Guard Low Side Hose For 34788 34288 34134Z Units. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure. Fittings are 7/16" Flare x 14MM Hose for Automotive R-134a.

Robinair Calibration Verification Weight (1.18lbs.). Easily maintain your units accuracy with this handy calibration weight. Ships with each new unit. This is a factory part, calibrated for accuracy.

Panel mount manifold Valve Assembly. High and Low side Manual valves that control the flow of refrigerant into the unit. Gauges are purchased separately.

Operating Manual for 34288 Recovery, Recycling, Recharging Unit. This is the original factory manual shipped with your unit, original print version "F". Also available as a download PDF file when you check out. You will receive both versions.

543176 Robinair Faceplate Decal 34288

543184 Robinair Internal Storage Vessel With Valve. The internal storage vessel (ISV) in this unit is a DOT-approved tank that carries a date code. This type of ISV must be re-certified or replaced every five years. To determine the date code of the ISV in your unit, remove the right side panel. It should be possible to read the date code stamped on the ISV. If the date code reads beyond the five-year limit, replace The Tank (you will need to strip the fittings and valves from the old tank). For the complete tank with all components see RA20089.

544023 Robinair Front Panel Sidewinder Cart, No decals or hardware, Grey.

544672 Robinair Ball Valve Assembly

557648 Robinair 34724 Filter O-Ring Small

557649 Robinair 34724 Filter O-Ring Large

Door Latch Kit Sidewinder Cabinets Device that contains spring, latch, retainer, and receptacle that holds door closed.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center. For a list of authorized service providers in your area, click here

Main Power Switch Controls the power between the power cord and the main board.

Caster 5" X 2" Swivel wheels mounted beneath unit for mobility.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve, This kit includes 1 check valve & O-ring. Allows flow in one direction only, towards the recovery solenoid, and prevents refrigerant from escaping out of the inlet after recovery and during recycling, evacuation and shutdown.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Start Kit for older style compressors (check service for applications) .
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Caster 5" X 2" Swivel wheels mounted beneath unit for mobility.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Door Latch Kit Sidewinder Cabinets Device that contains spring, latch, retainer, and receptacle that holds door closed.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Switch, 1/8 Male Pipe thread, Used to control solenoid operation from accumulator to waste oil bottle. Allows unit to dump waste oil recovered from vehicle. NOTE: Opens solenoid at 16psi and closes at 9psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Low Side Universal Replacement Compound Gauge -30" 0-125 PSI
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Universal Replacement Gauge 0-500 Psi/Bar/kPa pressure readings.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fastener Seal and hardware kit for Robinair recovery units is a service provider must have. This kit contains 38 of the most requested hardware and small maintenance items on most Robinair machines many of which are difficult or impossible to find by themselves, including gaskets seals, bolts and screws, pneumatic fittings, door latches, Torx screws, flare gaskets and other hard to find or specific related items. 3/8 Hose Gasket, 1/4 Fl Copper gasket, O'Rings, Screws Torx, Speed Nuts, Tinnerman U Clip, 1/2 Acme Jam nut, Pneumatic Fittings, Pan Head screws, Grommets, Door Latch Receptacle, Connector, Plastite connector, Bezel 7002K / 700Z, Door Latch Spring, Injector Bulkhead Fitting, Oil Injector Cap And Bulkhead Fitting, Vacuum Pump Fill Caps, Shreader Cores. Housed in a Double sided flip top case with extra space for other items.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Scale / Magnet Sends a signal to the main board for accurate weight readings during charging and recovery. Magnet is used to attach a calibrated steel ball underneath the unit for checking the scale's accuracy.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

3/8" High Pressure Tube 18" (each). Always use new tubing and 20006 ferrules when installing a new compressor.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20006 Robinair 3/8" Ferrule And Nut (each)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20007 Robinair 1/4 Ferrule And Nut (each)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Ferrule & Nut 1/8" (Sold Each)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

12 Volt Dc Discrete Solenoid
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

12 Volt DC Manifold Solenoid.
*If using on Models 34288 or EEAC324 units, Re-install the old coil with this new solenoid body.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Vacuum Relief Check Valve
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve Insert. Allows gas to flow in only one direction. Prevents backflow. Sold as a 6-pack (Coarse Thread Long)

Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve Insert. Allows gas to flow in only one direction. Prevents backflow. Sold Each. (Coarse Thread Long)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20019 Robinair Vacumaster Brass Oil Fill Plug & Seal
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Cubigel Compressor for 34788, 34288, 34988 units. Includes all hardware and electrical for a complete install. Additional Plastic tubes and compression rings (RA20006, RA20005) may be necessary to complete the install. Inspect all fittings for leaks before running unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20031 Robinair 1.5 CFM Vacuum Pump pulls moisture and air from the system to which the unit is attached.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20032 Robinair Manifold Block Assy 34288
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20033 Robinair Display - Control Board 34288. Installation of this part requires a service centers assistance to install properly.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20034 Robinair Keypad for 34288, provides means of input for operation of functions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20035 Robinair Power Supply 34288
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20066 Robinair Accumulator Transducer
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Air Purge Transducer. Replaces 539229.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20089 Robinair Internal Storage Vessel With Valve. The internal storage vessel (ISV) in this unit is a DOT-approved tank that carries a date code. This type of ISV must be re-certified or replaced every five years. To determine the date code of the ISV in your unit, remove the right side panel. It should be possible to read the date code stamped on the ISV. If the date code reads beyond the five-year limit, replace The Tank. For the tank only with no solenoid or valves; see 543184.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA30022 Robinair Check Valve New Style (Each). Allows gas to flow in only one direction. Prevents backflow. (Coarse Thread Short)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA30047 Robinair Tank Temperature Probe
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.