Robinair Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points.

112364 Robinair O-Ring For R-134a Quick Seal Fittings (Each). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

112634 Robinair Low Side Docking Spud for all sidewinder style carts

112635 Robinair High Side Docking Spud for all sidewinder style carts

112699 Robinair Oil Injector O-Ring

114692 Robinair Oil Bottle Cap for Oil Inject / Drain bottle, for 8 - 12 ounce oil injector bottles. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don't forget extra bottles (115642) for storing different oil types.

114693 Robinair Oil Bottle Cap (Less Liner With Holes) For Oil Injectors

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

12oz. Graduated Oil Drain - Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don forget extra caps (114692) for storing different oil types.

12oz. Graduated Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations. For storing alternative oils for injection & for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Includes cap & Level O-ring.

120225 Robinair 1/4" O.D. Oil Injector Tubing. For all "Side-Winder" Style Recovery Units. Sold By The Inch. See RA20007 Robinair 1/4 Ferrule And Nut (each).

36" of 1/8" Black Nylon Tube, used to connect low-side and high-side gauge to manifold block and connect oil drain block to drain.

Wiring Harness Main Power supply for ACR2000 ACR2005 342000. Transfers power from main supply to the power switch, relay board and to the power supply board.

121925 Robinair Velcro Refrigerant Tank Strap

Robinair Sidewinder Front Cabinet Panel. Fits all "Sidewinder" style carts. Installs in minutes with torx type screws (not included).

123785 Robinair Discharge Oil Coalescing Filter O-Ring

123786 Robinair Discharge Oil Filter Canister O-Ring

123787 Robinair Discharge Oil Coalescing Element separates oil from vapors in the discharge gas stream so it can be returned back to the compressor. This filter can become plugged when a compressor fails from a burn out or overheating due to waxes normally found in refrigerants.

Keep recovery and recycling units operating at peak efficiency with a convenient maintenance kit. Contains one quick change filter-drier to be used on either R-12 or R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil.  Designed for newer units manufactured after 1998.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

Forward Pumping section for 6 CFM Vacuum Pumps. Includes Pump, Iso Valve Installed, drain fitting and oil fill cap. For model 15600.

ROBINAIR 6 CFM 2 STAGE ROTARY VANE VACUUM PUMP Thoroughly evacuate todays tighter systems with their increased sensitivity to contaminants. Iso-Valve isolates pump from system, making it easy to measure rate of rise.

Robinair 10" Heavy Duty Foam Filled Pneumatic wheel with bearings for Sidewinder style Cart units. Replaces 19823. No more flat tires. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation and long life. Additional hardware for the unit is a Cotter Pin 1/8" Diameter X 1" Long & Flat Washer 1/2" I.D.

Identifier Filter For RI2004DX, 16900, 16910, 342000, ACR2000, ACR2005. When the element shows red any where in its body its time to replace it.

Parts Kit For Manifolds And Hoses Contains an assortment of the most commonly needed replacement parts for repairing manifolds, hoses and various other A/C tools.

Protect your investment with a heavy-duty vinyl dust cover. Features corded seams for durability; medium gray color with Cool-Tech logo. Fits 3420000, ACR2000, ACR2005, 177002K, 17700Z, 347002K, 34700Z, 34134Z series units.

Discontinued See 17492

Oil Drain Bottle For Robinair Sidewinder Cabinet Style Recovery Machines

17773 Robinair O-Ring For R-134a Quick Seal Fittings (2 Pack). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

Temp Probe Red 15ft ACR2000, ACR2005, 342000

Temp Probe 30ft Blue ACR2000, ACR2005, 342000

QUICK SEAL O-Ring Set (6 Pack), O-Rings made of durable silicone rubber for resilience and long life.  fits all 1/4" Flare Quickseal Hose Ends.

Lowside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

Highside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

18192 Robinair High/Low Side Service Couplers 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

19056 Robinair Heavy Duty Refrigerant Tank Strap With Buckle

O-Ring Kit For 18190A & 18191A Couplers

19740 Source Tank Filter For 134A units. Protect your investment from debris and harmful elements from tank manufacturing processes. Metal debris can foul solenoids causing unnecessary repairs and equipment failures. Install this filter on the hose end of your tank add hose to protect your machine. 100 mesh screen is replaceable or cleanable. 1/2" Female ACME X 1/2" Male ACME fittings Installs inline of tank fill hose.

Robinair 10" Heavy Duty Foam Filled Pneumatic wheel for Sidewinder style Cart units. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation and long life.

Robinair Oil Injector Cap (Steel) & the fitting is a 1/8 MPT x 5/16" press in hose capture device that also holds the cap in place. The included cap has a hole for mounting and 2 weep holes for equalization.. Replaces all earlier white plastic caps. For all "Side-Winder" Style Recovery Units.

Oil Injector Repair Kit. For all "Side-Winder" Style Recovery Units. Includes all necessary components to rebuild broken or missing oil injector bottle assemblies.

Printer Paper (2.35" Wide) 3 Pack For ACR2000 342000 ACR2005, Single Rolls of thermal paper for printers on advanced recovery units. When paper breaks down and your printer exhibits signs of not properly printing, try replacing the roll first.

The 34724 Robinair filter drier has been specifically formulated to trap acid and particulates and is formulated to remove water from the refrigerant. DO NOT accept look alike or knock off filters. You must change the filter-drier to assure adequate moisture and contaminant removal. Typically, you can recycle up to 300 pounds (136 kilograms) of R-134a or 600 pounds (272 kilograms) of refrigerant between filter changes (depending on your model). To help you know when you’ve reached that point, the unit displays the warning message prompting you to change the filter drier.

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

Printer Paper (1.5" Wide) Single Rolls of thermal paper for printers on advanced identifier units. When paper breaks down and your printer exhibits signs of not properly printing, try replacing the roll first. Thermal paper will deteriorate over time and no longer accept heat from the printing head.

523148 Robinair Oil Injector Steel Cap & Bulkhead Fitting used to attach the oil injector bottle to the unit, allowing user to inject oil into vehicle being serviced.

Oil Injector Cap used to attach the oil injector bottle to the unit, allowing user to inject oil into vehicle being serviced.

523477 Robinair Discharge Condenser Heat Exchanger Coil

539668 Robinair Suction Accumulator Canister O-Ring

544023 Robinair Front Panel Sidewinder Cart, No decals or hardware, Grey.

557648 Robinair 34724 Filter O-Ring Small

557649 Robinair 34724 Filter O-Ring Large

Door Latch Kit Sidewinder Cabinets Device that contains spring, latch, retainer, and receptacle that holds door closed.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center. For a list of authorized service providers in your area, click here

Caster 5" X 2" Swivel wheels mounted beneath unit for mobility.

Identifier Filter For Neutronics Identifiers. When the element shows red any where in its body its time to replace it.

96" Low Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

96" Low Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

Blue 240" Enviro-Guard Hose for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure.

Red 240" Enviro-Guard Hose for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure.

96" High Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

Set of Red/Blue 20’ Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant.

Recent production changes may affect your placement of this pump. The new pump was designed for 17800B cart style Recovery Recycling Units Only. For all other applications See 15548 For Replacement pumping section or RA19902 as a possible replacement.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Hose Screen Replacement in-line disc screen filter for copper tubing.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve Allows flow in one direction only and prevents pressure from back flowing into a particular path.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Switch 1/4 Flare Female Used to control solenoid operation from accumulator to waste oil bottle. Allows unit to dump waste oil recovered from vehicle. NOTE: Opens solenoid at 16psi and closes at 9psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve, This kit includes 1 check valve & O-ring. Allows flow in one direction only, towards the recovery solenoid, and prevents refrigerant from escaping out of the inlet after recovery and during recycling, evacuation and shutdown.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Switch If pressure inside the unit exceeds 435psi, the switch opens, stopping all functions of unit. NOTE: Switch opens at 435psi +/- 10psi and resets at 320psi +/- 20psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

110v Compressor With O-Ring Fittings - Discontinued - See RA19865
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Pressure Relief Valve Safety valve on tank or internal storage vessel that opens if internal tank pressure exceeds 450psi. Valve has been designed, constructed and rated in accordance with ANSI/ASHRAE 15 -1994 Standard Safety Code for Mechanical Refrigeration Standards Association.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve 1/4" O-Ring > 1/8 M Pipe A two port valve, that normally allows fluid (liquid or gas) to flow through it in only one direction.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Expansion Valve Single Port Meters the flow of refrigerant into the system oil separator. The allowable tolerance of the valve is 35 +/- 5 psi (241 +/- 34 kPa).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Male Coupler Connects small black nylon hose to Oil Drain Assembly for draining oil into waste oil bottle.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Manifold Block Assembly ACR2000 Internal block assembly that contains solenoids, check valves, and switches. Refrigerant will pass through the manifold assembly for proper distribution.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Block Assembly ACR2000 Lower Internal block assembly that contains solenoids, check valves, and switches.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Relay Board ACR2000 Controls power to internal components 110v and 12v output.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Scale Assembly Sends a signal to the main board for accurate weight readings during charging and recovery (strain gauge style).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Identifier - ACR2000 Samples the refrigerant inside unit and vehicle being serviced, and analyzes refrigerant for R12, R22, R134a, and hydrocarbons.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Identifier ACR2000 - See Also RBTRA19604a Samples the refrigerant inside unit and vehicle being serviced, and analyzes refrigerant for R12, R22, R134a, and hydrocarbons.B245
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Analog Board ACR2000 External sensor board where the RS-232 communication port, the red and blue temperature probes and the air flow probe connections are located.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Ambient Board ACR2000 Circuit board that measures air temperature and humidity.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Vacuum Pump Assembly ACR2000 An oilless pump that pulls moisture and air from the system to which the unit is attached.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Printer Assembly ACR2000 Prints the snapshot information displayed on screen.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Internal Storage Vessel Storage Tank, used to store recovered refrigerant. NOTE: This is the Old style tank with ball valves. If your unit has the new style tank with QuickSeal fittings see RA19798.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge ACR2000 - Used to monitor the discharge pressure of the vehicle being serviced. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19614 Low Side 134A Gauge With Indicator Lens ACR2000 - Used to monitor the suction pressure of the vehicle being serviced. Includes mounting hardware and instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Condenser Assembly ACR2000 Turns vapor refrigerant to liquid refrigerant for delivery to the Internal Storage Vessel (ISV).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Caster 5" X 2" Swivel wheels mounted beneath unit for mobility.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Door Latch Kit Sidewinder Cabinets Device that contains spring, latch, retainer, and receptacle that holds door closed.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Pressure Transducer ACR2000 Measures the pressure of incoming refrigerant from the high side of a system. Pressure readings are then relayed to the control/display board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Identifier Switch ACR2000 This normally closed switch will cause the inlet test solenoid to close if the pressure of the sampled refrigerant is above 40 +/- 3 psi (276 +/- 21 kPa). The switch controls the flow of refrigerant to the identifier. It will reset at 27 +/- 3 psi (276 +/- 21kPa).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Isv Air Purge Hose Allows air pressure trapped at the top of the ISV to enter the lower cavity of the Air Purge device during recycling.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Isv Liquid Hose Supplies liquid refrigerant from internal tank to charging solenoid on manifold block for adding refrigerant to vehicle.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Isv Vapor Hose Allows the flow of recovered refrigerant from the manifold block into the internal tank (ISV).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Gauge Lens - Discontinued - See RO19639 Clear protective cover for the high side and low side gauges. See individual Gauges for a replacement.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Low Side Pressure Transducer ACR2000 Measures the pressure of incoming refrigerant from the low side of a system. Pressure readings are then relayed to the control/display board. Also determines if recovery is needed. Stops recovery at 13 psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19641 Robinair Power Cord 15'. 16 gauge SJTO (Black, White, Green) wire with male quick disconnect terminals.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Pipe Check Valve RBT Kit Prevents incoming refrigerant from opening the filter vacuum solenoid during normal operations.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Sandwich Check Valve RBT Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Rebuild Kit No / Solenoid Open ACR2000 Normally open solenoid receiving power one second after the vacuum pump starts. This process allows the vacuum pump to start with free air on the inlet. The solenoid should maintain power for the complete vacuum cycle.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Id Oil Separator Prevents oil from entering ID unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Switch, 1/8 Male Pipe thread, Used to control solenoid operation from accumulator to waste oil bottle. Allows unit to dump waste oil recovered from vehicle. NOTE: Opens solenoid at 16psi and closes at 9psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Discontinued Control Module 342000 User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit. (Can be replaced with RA19606A and reprogrammed to match)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Low Side Gauge - Generic Used to monitor the suction pressure of the vehicle being serviced. 1/8" female pipe connection back tap. -30hg-0 To 0-125 PSI Range, 350 PSI Retard, PSI, Kpa, Bar Pressure Scales On Face. Includes Mounting Hardware, Loctite sealant, Instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge - Generic Used to monitor the discharge pressure of the vehicle being serviced. 1/8" female pipe connection back tap. 0-500 PSI Range, PSI, Kpa, Bar Pressure Scales On Face. Includes Mounting Hardware and Instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Install Kit ACR2000 / ACR2005 & 342000 Units To Use new style Cubigel Compressor
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Cubigel Compressor (Replaces The RA17110, RA17434, RA19458, & RA19748) Includes all hardware and electrical for a complete install. See additional plumbing retrofit kits noted for older style units.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19870 Robinair RA19604A Refrigerant Identifier Rebuild Kit. This kit is not a guaranteed repair. It is designed to be an optional or possible repair for your identifier, NOT a replacement kit for the identifier. SPX does not guarantee this kit will correct all identifier failures.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Rebuild your refrigerant identifier Pump on a Robinair ACR200 & 342000 models for a fraction of the cost of replacement. Our new rebuild kit includes rubber gaskets and flapper valves for your pump. Simply remove old pump from the board and rebuild with the gaskets included and that’s it. Typical failures are "Contaminated or 100% Air" and are due to no flow or low flow from the sample chamber pump.

Check Valve Kit (Block Style Units) Prevents incoming refrigerant from opening the charge solenoid and entering the liquid side of the ISV.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Repair kit with Oil Injector Caps (20) and bulkhead fitting (10) Used to attach the oil injector bottle to the unit, allowing user to inject oil into vehicle being serviced. See 523148
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fastener Seal and hardware kit for Robinair recovery units is a service provider must have. This kit contains 38 of the most requested hardware and small maintenance items on most Robinair machines many of which are difficult or impossible to find by themselves, including gaskets seals, bolts and screws, pneumatic fittings, door latches, Torx screws, flare gaskets and other hard to find or specific related items. 3/8 Hose Gasket, 1/4 Fl Copper gasket, O'Rings, Screws Torx, Speed Nuts, Tinnerman U Clip, 1/2 Acme Jam nut, Pneumatic Fittings, Pan Head screws, Grommets, Door Latch Receptacle, Connector, Plastite connector, Bezel 7002K / 700Z, Door Latch Spring, Injector Bulkhead Fitting, Oil Injector Cap And Bulkhead Fitting, Vacuum Pump Fill Caps, Shreader Cores. Housed in a Double sided flip top case with extra space for other items.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Ferrule & Nut 1/8" (Sold Each)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20058 Robinair 34788 / ACR2000-ACR2005 Hose Flush Update Kit. This update applies to All ACR200 ACR2005 & 34788 units. All 34788 units manufactured July 2008 already have this feature. When adding the Hose Flush feature, the software in your 34788 unit must be 1.092 or newer. Please Call for assistance for updating your software.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.