Robinair 120v heater blanket speeds charging by maintaining a constant temperature at the tank, thus creating a positive pressure differential between the refrigerant source and the A/C system.

110973 Robinair Operating Manual For 15400 15600 Vacuum Pump. This is the original factory manual shipped with your unit. Available as Hard Copy and a download PDF file when you check out. You will receive both.

112364 Robinair O-Ring For R-134a Quick Seal Fittings (Each). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

112699 Robinair Oil Injector O-Ring

114692 Robinair Oil Bottle Cap for Oil Inject / Drain bottle, for 8 - 12 ounce oil injector bottles. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don't forget extra bottles (115642) for storing different oil types.

114693 Robinair Oil Bottle Cap (Less Liner With Holes) For Oil Injectors

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

12oz. Graduated Oil Drain - Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don forget extra caps (114692) for storing different oil types.

12oz. Graduated Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations. For storing alternative oils for injection & for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Includes cap & Level O-ring.

123785 Robinair Discharge Oil Coalescing Filter O-Ring

123786 Robinair Discharge Oil Filter Canister O-Ring

123787 Robinair Discharge Oil Coalescing Element separates oil from vapors in the discharge gas stream so it can be returned back to the compressor. This filter can become plugged when a compressor fails from a burn out or overheating due to waxes normally found in refrigerants.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

Robinair Handle Power Cord Switch Assembly 15400 - 15600 Series Pumps. Kit includes Handle, Power Cord, Switch, butt connectors, screws for mounting and o-rings for the exhaust vent banjo bolt.

Forward Pumping section for 6 CFM Vacuum Pumps. Includes Pump, Iso Valve Installed, drain fitting and oil fill cap. For model 15600.

ROBINAIR 6 CFM 2 STAGE ROTARY VANE VACUUM PUMP Thoroughly evacuate todays tighter systems with their increased sensitivity to contaminants. Iso-Valve isolates pump from system, making it easy to measure rate of rise.

Low Side Tank Adapter. 1/2" ACME Female X Lowside Spud used for tank fill and maintenance procedures. 1/2" ACME Female x Low-Side R-134a Coupler

Parts Kit For Manifolds And Hoses Contains an assortment of the most commonly needed replacement parts for repairing manifolds, hoses and various other A/C tools.

8oz. Graduated Oil Drain - Oil Injector Bottle. 8oz Capacity in 1/2oz graduations and 240 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigernt recovery process.

50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

50 Lb. Refillable Refrigerant Tank Float Switch. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

RO17641 Recycle Guard Hose Install Kit For R-12 and R-134A Installs. Comes Complete with hoses and fittings for Installation of a RO17622 RecycleGuard Filter.
Discontinued See the following part numbers
For R-134A Installation 1) RO19078 36" ACME Hose 1) MSC80296 1/8" MPT X 1/2" ACME Adapter
For R-12 / Other Gases 1) RO31036 36" Flare Hose 1) MSC90296 1/8" MPT X 1/4" Flare Adapter

XH-9 Filter Drier For 17800A 178002K Series Recovery Recycling Units. Specifically formulated using XH9 drier desiccant to trap acid and particulates and is formulated to remove water from the refrigerant. You must change the filter-drier to assure adequate moisture and contaminant removal.

17773 Robinair O-Ring For R-134a Quick Seal Fittings (2 Pack). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

The 17800C is ideal for refrigerated trailers, buses, RVs, and other vehicles that use more than one refrigerant and have system charges greater than 6 pounds. The 17800B Recovers, Recycles, Evacuates, and Recharges R-12, R-134a, R-22, R-502, R-404, MP and HP Blends and many more! all in one fast, continuous operation through one hook-up.

Lowside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

Highside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

18192 Robinair High/Low Side Service Couplers 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

Power Cord - 110 Volt 16 Gauge. For heay duty cord see 551628.

O-Ring Kit For 18190A & 18191A Couplers

96" Red Ball Valve End Hose for High Pressure gases. Ball Valve end prevents gas leakage or loss when removing hoses from their fittings. Safe for use on all refrigerants.

96" Blue Ball Valve End Hose for High Pressure gases. Ball Valve end prevents gas leakage or loss when removing hoses from their fittings. Safe for use on all refrigerants.

19299 Robinair 36" Yellow Quick-Seal Enviro-Guard Tank Hose 1/4" Flare For R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Quick-Seal Fittings prevent pressure release when disconnected form their fittings.

36" Blue Quickseal Hose - Discontinued - See RO19350 R134a blue liquid tank hose. Allows flow from liquid port on tank to unit for charging vehicle.

19307 Robinair 36" Red Double Quick-Seal Enviro-Guard Tank Hose R134A. Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

19308 Robinair 36" Red Double Quick-Seal Enviro-Guard Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction.  740 psi working pressure, 3700 psi burst pressure.

19309 Robinair 96" Blue Double Quick-Seal Enviro-Guard Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12and other gases. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction.  740 psi working pressure, 3700 psi burst pressure.

19310 Robinair 36" Yellow Double Quick-Seal Enviro-Guard Tank Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19312 Robinair 36" Red Double Quick-Seal Enviro-Guard Tank Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19313 Robinair 36" Yellow Double Quick-Seal Enviro-Guard Tank Hose R134A. Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

96" High Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

96" Low Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

36" Blue Double Quick-Seal Enviro-Guard Tank Hose R134A. Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant

19370 Robinair 96" Red Double Quick-Seal Enviro-Guard Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19372 Robinair 36" Blue Double Quick-Seal Enviro-Guard Tank Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19375 Robinair 36" Blue Quick-Seal Enviro-Guard Tank Hose 1/4" Flare for R12 and other gasses. Enviro-Guard Hoses for Automotive R-12. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19740 Source Tank Filter For 134A units. Protect your investment from debris and harmful elements from tank manufacturing processes. Metal debris can foul solenoids causing unnecessary repairs and equipment failures. Install this filter on the hose end of your tank add hose to protect your machine. 100 mesh screen is replaceable or cleanable. 1/2" Female ACME X 1/2" Male ACME fittings Installs inline of tank fill hose.

10 In. Pneumatic Wheel 5/8" Axle For Sidewinder Style Units. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation.

50lb. R-134a Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve and a third port for vapor/air purge (a must for 3 hose recovery units). 50 lb. capacity refrigerant tank for R-134a with 1/2" ACME fittings. Fits models 12134, 34700, 17534, 17800 series

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

539668 Robinair Suction Accumulator Canister O-Ring

551628 PROMAX Power Cord 115 Volt 14 Gauge

Main Power Switch Controls the power between the power cord and the main board.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

68336A Robinair 36" Red Enviro-Guard Hose 45 Degree Quick Seal Fitting 1/4" Flare for R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

Recent production changes may affect your placement of this pump. The new pump was designed for 17800B cart style Recovery Recycling Units Only. For all other applications See 15548 For Replacement pumping section or RA19902 as a possible replacement.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

System Relay 115 volt coil, double pole single throw normally open switch with dual sets of 15 amp contacts. Acts as a pilot from the circuit board usually carrying higher amp loads to protect smaller relays on board. Can be used for universal applications due to the high amp contact rating.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to force air through the evaporator/condenser.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Brass Panel Valve Allows flow from the low or high side hose into the center manifold tube (suction line strainer). RA19199 Manifold Stem Repair Kit for older valves.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Grounded recepticle that acessories plug into
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Robinair Keypad 17700 34700 (See RA19253 For New Style Keypad/Decal) - Sends controlling signals to program the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Cutout 17650 / 17655 A normally closed sensor that opens, stopping the recovery process when the compressor discharge pressure reaches 435 psi. SPDT Contact arrangement. 1/4 spade termination.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Vacuum Pump Protection Switch (RA17329 Old Style) - A normally open switch that closes if pressure greater than 25 psi is present. Prevents damage to vacuum pump.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board - Discontinued User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

120 Volt 25 Watt Heater Band. Heat is applied to the system oil separator to assist in vaporizing the refrigerant before entering the compressor. Includes Heater Band, Thermal Insulation wrap, Foil Tape, 1/4" Female Faston Wire connectors. Fits 4" Diameter Vessels. +/- 1/4".
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Air Purge Gauge Used to monitor refrigerant tank pressure. Correlate with PT chart to monitor air percentage. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board - Discontinued User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve, This kit includes 1 check valve & O-ring. Allows flow in one direction only, towards the recovery solenoid, and prevents refrigerant from escaping out of the inlet after recovery and during recycling, evacuation and shutdown.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Discontinued See RA19804 Float Chamber 17800 Series Liquid Vapor discrimination chamber switches gas modes on recovery and recycle modes for faster flow of liquid
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Lockout Box Assembly Prevents the user from switching the gas mode on a recovery unit with out doing a clear or refrigerant change
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board 17801a User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board 17800a User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Low Side Gauge Reads pressure and/or vacuum entering the low side hose. Panel mount & nuts included. 1/8" Female Pipe Thread connection. See RA19257 2-3/4" Replacement Gauge Lens
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge ACR2000 - Used to monitor the discharge pressure of the vehicle being serviced. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19614 Low Side 134A Gauge With Indicator Lens ACR2000 - Used to monitor the suction pressure of the vehicle being serviced. Includes mounting hardware and instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board 34801 User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge - Generic Used to monitor the discharge pressure of the vehicle being serviced. 1/8" female pipe connection back tap. 0-500 PSI Range, PSI, Kpa, Bar Pressure Scales On Face. Includes Mounting Hardware and Instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Pumps the refrigerant from system being serviced into the ISV or tank, on unit, for storage. If installing this as a retrofit replacement for the original compressor, see the installation tubing kit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Retrofit Kit For17800 Series Copper lines and tubes used to retrofit unit for new style compressor.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Float Chamber 17800B Magnetic float switch that sends a signal to the main circuit board when liquid is entering the system. The RA19804 Series bottle switch is a compact, economical liquid level sensing device for external mounting in applications not suited to small, internally-mounted level switches. These single point devices are typically used for low or high level sensing. 1/4" NPT Inlet (Bottle) 1/8" NPT Outlet (Cap).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Dual bulb thermostatic expansion valve controls flow of refrigerant to the inlet and outlet of the suction accumulator of the unit. Unique design uses two sample bulbs to control the amount of liquid refrigerant that enters the coaxial coil.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve Kit (Block Style Units) Prevents incoming refrigerant from opening the charge solenoid and entering the liquid side of the ISV.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fastener Seal and hardware kit for Robinair recovery units is a service provider must have. This kit contains 38 of the most requested hardware and small maintenance items on most Robinair machines many of which are difficult or impossible to find by themselves, including gaskets seals, bolts and screws, pneumatic fittings, door latches, Torx screws, flare gaskets and other hard to find or specific related items. 3/8 Hose Gasket, 1/4 Fl Copper gasket, O'Rings, Screws Torx, Speed Nuts, Tinnerman U Clip, 1/2 Acme Jam nut, Pneumatic Fittings, Pan Head screws, Grommets, Door Latch Receptacle, Connector, Plastite connector, Bezel 7002K / 700Z, Door Latch Spring, Injector Bulkhead Fitting, Oil Injector Cap And Bulkhead Fitting, Vacuum Pump Fill Caps, Shreader Cores. Housed in a Double sided flip top case with extra space for other items.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the electrical power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.