Robinair Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points.

106845 Robinair Oil Injector Dip Tube 5/16 OD X 4.25 Long

Wheel For Cart Style Stations

110138 Robinair Tinnerman Clips Speednut Bracket - 90 Degree. (5 Pack) for Upper Gray Shroud For Cart Style Recovery Units.

110973 Robinair Operating Manual For 15400 15600 Vacuum Pump. This is the original factory manual shipped with your unit. Available as Hard Copy and a download PDF file when you check out. You will receive both.

112699 Robinair Oil Injector O-Ring

114692 Robinair Oil Bottle Cap for Oil Inject / Drain bottle, for 8 - 12 ounce oil injector bottles. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don't forget extra bottles (115642) for storing different oil types.

114693 Robinair Oil Bottle Cap (Less Liner With Holes) For Oil Injectors

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

12oz. Graduated Oil Drain - Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don forget extra caps (114692) for storing different oil types.

12oz. Graduated Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations. For storing alternative oils for injection & for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Includes cap & Level O-ring.

121925 Robinair Velcro Refrigerant Tank Strap

Contains one quick change filter-drier to be used on both R-12 and R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil. For early models using 34430 Filter-Drier (17700A, 34700, 34300-2K). See your instruction manual if you have questions about which filter-drier to use.

Keep recovery and recycling units operating at peak efficiency with a convenient maintenance kit. Contains one quick change filter-drier to be used on either R-12 or R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil.  Designed for newer units manufactured after 1998.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

Robinair Handle Power Cord Switch Assembly 15400 - 15600 Series Pumps. Kit includes Handle, Power Cord, Switch, butt connectors, screws for mounting and o-rings for the exhaust vent banjo bolt.

Forward Pumping section for 6 CFM Vacuum Pumps. Includes Pump, Iso Valve Installed, drain fitting and oil fill cap. For model 15600.

ROBINAIR 6 CFM 2 STAGE ROTARY VANE VACUUM PUMP Thoroughly evacuate todays tighter systems with their increased sensitivity to contaminants. Iso-Valve isolates pump from system, making it easy to measure rate of rise.

Parts Kit For Manifolds And Hoses Contains an assortment of the most commonly needed replacement parts for repairing manifolds, hoses and various other A/C tools.

8oz. Graduated Oil Drain - Oil Injector Bottle. 8oz Capacity in 1/2oz graduations and 240 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigernt recovery process.

50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

RO17641 Recycle Guard Hose Install Kit For R-12 and R-134A Installs. Comes Complete with hoses and fittings for Installation of a RO17622 RecycleGuard Filter.
Discontinued See the following part numbers
For R-134A Installation 1) RO19078 36" ACME Hose 1) MSC80296 1/8" MPT X 1/2" ACME Adapter
For R-12 / Other Gases 1) RO31036 36" Flare Hose 1) MSC90296 1/8" MPT X 1/4" Flare Adapter

19056 Robinair Heavy Duty Refrigerant Tank Strap With Buckle

19205 36" Yellow Tank Hose W / Depressors. Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

Valve Stem rebuild kit, for units with old style panel valves. Identifiable by the center screw holding the stem in place with plastic removable handles. This kit does not repair "Kantleak" style valves, those must be replaced with new valves.

19256 Robinair Gauge Lens 2.25 in. For 17700 RA17708 RA17709 old style gauges. Check the bevel of your lens to ensure it matches this lens profile. Newer style lenses have a sharp 45 degree angled outer ring these have a arched outer ring.

Red Cap For Asco Solenoid

Lower Gray Shroud For Cart Style Recovery Units. Replaces all other color shrouds.

The Robinair 34430 filter-drier has been specifically formulated using XH9 drier desiccant to trap acid and particulates and is formulated to remove water from the refrigerant. You must regularly change the 34430 filter-drier to assure adequate moisture and contaminant removal.

The 34724 Robinair filter drier has been specifically formulated to trap acid and particulates and is formulated to remove water from the refrigerant. DO NOT accept look alike or knock off filters. You must change the filter-drier to assure adequate moisture and contaminant removal. Typically, you can recycle up to 300 pounds (136 kilograms) of R-134a or 600 pounds (272 kilograms) of refrigerant between filter changes (depending on your model). To help you know when you’ve reached that point, the unit displays the warning message prompting you to change the filter drier.

These depressors fit behind and protrude through the hose gasket on 1/4" flare and 1/2 ACME standard fittings. If you are replacing hose gaskets it's a good idea to replace these as well.

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

Gaskets For 3/8" Charging Hose (Pkg. Of 6)

557648 Robinair 34724 Filter O-Ring Small

557649 Robinair 34724 Filter O-Ring Large

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

68336A Robinair 36" Red Enviro-Guard Hose 45 Degree Quick Seal Fitting 1/4" Flare for R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

Recent production changes may affect your placement of this pump. The new pump was designed for 17800B cart style Recovery Recycling Units Only. For all other applications See 15548 For Replacement pumping section or RA19902 as a possible replacement.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Inlet Check Valve - 1/4 M Flare X 1/4 M Flare A two port valve, that normally allows fluid (liquid or gas) to flow through it in only one direction.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain / Injection Bottle Part Number Change See 17419
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA17434 Discontinued See 19865
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

System Relay 115 volt coil, double pole single throw normally open switch with dual sets of 15 amp contacts. Acts as a pilot from the circuit board usually carrying higher amp loads to protect smaller relays on board. Can be used for universal applications due to the high amp contact rating.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA18759 Robinair Air Purge Gauge And Thermometer gives the operator a visual cue as to the air content of a cylinder during recycling mode. Operates on a pressure temperature equivalence similar to a pressure temperature chart. The temp scale reads from the red needle and the pressure scale reads from the green needle. All that is needed is to compare the needles on the gauge to determine if air is present.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

System Oil Separator Separates oil from refrigerant. Internal heat causes incoming saturated vapor to evaporate. This is important to be sure no liquid enters the compressor and that oil droplets contained in the incoming refrigerant will drop out in the separator. This also works as a heat exchanger.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Complete Refrigerant Solenoid Assembly (120v) Includes brass body and coil. A normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Brass Panel Valve Allows flow from the low or high side hose into the center manifold tube (suction line strainer). RA19199 Manifold Stem Repair Kit for older valves.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Grounded recepticle that acessories plug into
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

PC Board Main Board - User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

PC Board Main Board - User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Robinair Keypad 17700 34700 (See RA19253 For New Style Keypad/Decal) - Sends controlling signals to program the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Sonalert 17700 Sounds an audible tone when commands are programmed through the keypad.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Return Oil Separator Traps compressor oil that has migrated out with refrigerant while passing through the compressor. NOTE: Some units have an automatic oil return controlled through the main board. When the compressor runs continuously for 10 minutes, the main board drops power to the equalization solenoid for 3 seconds and then re-powers it.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

(2?) High Side Gauge ? Reads pressure entering the high side hose. Note that the gauge will read pressure in the high side hose with the high side valve closed. 19257 (2?") Replacement Gauge Lens.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19076 (2?") Low Side Gauge ? Reads pressure and/or vacuum entering the low side hose. Note that the gauge will read pressure and/or vacuum in the low side hose with the low side valve closed. 19257 (2?") Replacement Gauge Lens
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Cutout 17650 / 17655 A normally closed sensor that opens, stopping the recovery process when the compressor discharge pressure reaches 435 psi. SPDT Contact arrangement. 1/4 spade termination.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Automatic Air Purge (Old Style) Used to purge excessive air from refrigerant tank during vacuum or recycle process. - FOR NEW STYLE SEE RA19242
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Discontinued Part Number (See 19427)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Discontinued Part Number (See 19427)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Faceplate Overlay Keypad attaches to the circuit board to select start,
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Lens - Discontinued - See RO19256
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Lens - Discontinued - See RO19257
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Low Side Gauge Reads pressure and/or vacuum entering the low side hose. Panel mount & nuts included. 1/8" Female Pipe Thread connection. See RA19257 2-3/4" Replacement Gauge Lens
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19641 Robinair Power Cord 15'. 16 gauge SJTO (Black, White, Green) wire with male quick disconnect terminals.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Cubigel Compressor (Replaces The RA17110, RA17434, RA19458, & RA19748) Includes all hardware and electrical for a complete install. See additional plumbing retrofit kits noted for older style units.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fastener Seal and hardware kit for Robinair recovery units is a service provider must have. This kit contains 38 of the most requested hardware and small maintenance items on most Robinair machines many of which are difficult or impossible to find by themselves, including gaskets seals, bolts and screws, pneumatic fittings, door latches, Torx screws, flare gaskets and other hard to find or specific related items. 3/8 Hose Gasket, 1/4 Fl Copper gasket, O'Rings, Screws Torx, Speed Nuts, Tinnerman U Clip, 1/2 Acme Jam nut, Pneumatic Fittings, Pan Head screws, Grommets, Door Latch Receptacle, Connector, Plastite connector, Bezel 7002K / 700Z, Door Latch Spring, Injector Bulkhead Fitting, Oil Injector Cap And Bulkhead Fitting, Vacuum Pump Fill Caps, Shreader Cores. Housed in a Double sided flip top case with extra space for other items.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the electrical power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.