106845 Robinair Oil Injector Dip Tube 5/16 OD X 4.25 Long

112699 Robinair Oil Injector O-Ring

114692 Robinair Oil Bottle Cap for Oil Inject / Drain bottle, for 8 - 12 ounce oil injector bottles. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don't forget extra bottles (115642) for storing different oil types.

114693 Robinair Oil Bottle Cap (Less Liner With Holes) For Oil Injectors

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

12oz. Graduated Oil Drain - Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don forget extra caps (114692) for storing different oil types.

12oz. Graduated Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations. For storing alternative oils for injection & for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Includes cap & Level O-ring.

36" of 1/8" Black Nylon Tube, used to connect low-side and high-side gauge to manifold block and connect oil drain block to drain.

121829 Robinair 1/4-20 3/4" Pan Torx Screw (Each)

121829-PK5 Robinair 1/4-20 3/4" Pan Torx Screw (5 Pack)

Robinair Power Cord Bracket. "U" shaped metal bracket that holds the strain relief bushing and power cord in place at entry point of unit.

121925 Robinair Velcro Refrigerant Tank Strap

121829 Robinair 1/4-20 3/4" Pan Torx Screw (Each)

Robinair Sidewinder Front Cabinet Panel. Fits all "Sidewinder" style carts. Installs in minutes with torx type screws (not included).

122745 Robinair Light Hole Cover For Sidewinder Top

Power Cord 15' Euro Colors Power Cord 15' Supplies main power to the unit.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

123785 Robinair Discharge Oil Coalescing Filter O-Ring

123786 Robinair Discharge Oil Filter Canister O-Ring

123787 Robinair Discharge Oil Coalescing Element separates oil from vapors in the discharge gas stream so it can be returned back to the compressor. This filter can become plugged when a compressor fails from a burn out or overheating due to waxes normally found in refrigerants.

Power Harness for 347002K 34700Z connects main power switch to main board. Board connection P10.

Breaker Harness for 347002K 34700Z connects circuit breakers to main board. Board connection P11 and spade terminal connections 38, 39, 40 & 41.

124006 Robinair High Pressure Wire Harness 347002K 34700Z connects high pressure switch to main board. Board connection P28.

Keep recovery and recycling units operating at peak efficiency with a convenient maintenance kit. Contains one quick change filter-drier to be used on either R-12 or R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil.  Designed for newer units manufactured after 1998.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

Forward Pumping section for 6 CFM Vacuum Pumps. Includes Pump, Iso Valve Installed, drain fitting and oil fill cap. For model 15600.

ROBINAIR 6 CFM 2 STAGE ROTARY VANE VACUUM PUMP Thoroughly evacuate todays tighter systems with their increased sensitivity to contaminants. Iso-Valve isolates pump from system, making it easy to measure rate of rise.

Robinair 10" Heavy Duty Foam Filled Pneumatic wheel with bearings for Sidewinder style Cart units. Replaces 19823. No more flat tires. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation and long life. Additional hardware for the unit is a Cotter Pin 1/8" Diameter X 1" Long & Flat Washer 1/2" I.D.

Protect your investment with a heavy-duty vinyl dust cover. Features corded seams for durability; medium gray color with Cool-Tech logo. Fits 3420000, ACR2000, ACR2005, 177002K, 17700Z, 347002K, 34700Z, 34134Z series units.

Discontinued See 17492

Oil Drain Bottle For Robinair Sidewinder Cabinet Style Recovery Machines

QUICK SEAL O-Ring Set (6 Pack), O-Rings made of durable silicone rubber for resilience and long life.  fits all 1/4" Flare Quickseal Hose Ends.

19056 Robinair Heavy Duty Refrigerant Tank Strap With Buckle

Robinair 10" Heavy Duty Foam Filled Pneumatic wheel for Sidewinder style Cart units. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation and long life.

Robinair Oil Injector Cap (Steel) & the fitting is a 1/8 MPT x 5/16" press in hose capture device that also holds the cap in place. The included cap has a hole for mounting and 2 weep holes for equalization.. Replaces all earlier white plastic caps. For all "Side-Winder" Style Recovery Units.

Oil Injector Repair Kit. For all "Side-Winder" Style Recovery Units. Includes all necessary components to rebuild broken or missing oil injector bottle assemblies.

The 34724 Robinair filter drier has been specifically formulated to trap acid and particulates and is formulated to remove water from the refrigerant. DO NOT accept look alike or knock off filters. You must change the filter-drier to assure adequate moisture and contaminant removal. Typically, you can recycle up to 300 pounds (136 kilograms) of R-134a or 600 pounds (272 kilograms) of refrigerant between filter changes (depending on your model). To help you know when you’ve reached that point, the unit displays the warning message prompting you to change the filter drier.

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

523148 Robinair Oil Injector Steel Cap & Bulkhead Fitting used to attach the oil injector bottle to the unit, allowing user to inject oil into vehicle being serviced.

Oil Injector Cap used to attach the oil injector bottle to the unit, allowing user to inject oil into vehicle being serviced.

523477 Robinair Discharge Condenser Heat Exchanger Coil

539668 Robinair Suction Accumulator Canister O-Ring

544023 Robinair Front Panel Sidewinder Cart, No decals or hardware, Grey.

557648 Robinair 34724 Filter O-Ring Small

557649 Robinair 34724 Filter O-Ring Large

Door Latch Kit Sidewinder Cabinets Device that contains spring, latch, retainer, and receptacle that holds door closed.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center. For a list of authorized service providers in your area, click here

Main Power Switch Controls the power between the power cord and the main board.

Caster 5" X 2" Swivel wheels mounted beneath unit for mobility.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

Recent production changes may affect your placement of this pump. The new pump was designed for 17800B cart style Recovery Recycling Units Only. For all other applications See 15548 For Replacement pumping section or RA19902 as a possible replacement.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

System Relay 115 volt coil, double pole single throw normally open switch with dual sets of 15 amp contacts. Acts as a pilot from the circuit board usually carrying higher amp loads to protect smaller relays on board. Can be used for universal applications due to the high amp contact rating.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Breaker 3 Amp Protects the unit from drawing too much current. If tripped, controller is inoperative.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Breaker 15 Amp Protects the unit from drawing too much current. If tripped, unit is completely inoperative.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Grounded recepticle that acessories plug into
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Switch 1/4 Flare Female Used to control solenoid operation from accumulator to waste oil bottle. Allows unit to dump waste oil recovered from vehicle. NOTE: Opens solenoid at 16psi and closes at 9psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve, This kit includes 1 check valve & O-ring. Allows flow in one direction only, towards the recovery solenoid, and prevents refrigerant from escaping out of the inlet after recovery and during recycling, evacuation and shutdown.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Switch If pressure inside the unit exceeds 435psi, the switch opens, stopping all functions of unit. NOTE: Switch opens at 435psi +/- 10psi and resets at 320psi +/- 20psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Vacuum Pump Protection Switch Normally open switch closes at 25psi and reopens at 10psi. Prevents vacuum pump from starting when pressure exists in vehicle's system.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Manifold Block Assembly 110v Complete Internal block assembly that contains all of the solenoids, check valves, switches, accumulator, and oil separator.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Automatic Expansion Valve Meters the flow of refrigerant into the unit oil separator. Allowable pressure setting of 35 psi +/- 1
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Control Board User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit. Does not include keypad.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Transformer Takes line voltage and steps it down to 12 volts for control circuit board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Internal Storage Vessel Storage Tank, used to store recovered refrigerant. NOTE: This is the Old style tank with ball valves. If your unit has the new style tank with QuickSeal fittings see RA19798.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge ACR2000 - Used to monitor the discharge pressure of the vehicle being serviced. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Caster 5" X 2" Swivel wheels mounted beneath unit for mobility.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Door Latch Kit Sidewinder Cabinets Device that contains spring, latch, retainer, and receptacle that holds door closed.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Switch, 1/8 Male Pipe thread, Used to control solenoid operation from accumulator to waste oil bottle. Allows unit to dump waste oil recovered from vehicle. NOTE: Opens solenoid at 16psi and closes at 9psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Keypad 347002K & 348002K User input device attached to a circuit board to select start, stop, and program functions of the unit. Easy install decal. Designed for 347002K units 9999 serial or lower and 348002K Units 29999 serial and lower. (Older units can be identified by having only 3 screws holding the Keypad bezel in place, newer units have 4 screws holding the Control module in place.)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Control Board 347002K (s/n 9999 and lower) Controls the function of the unit with input from the user via keypad. NOTE: Units with serial # 9999 and lower.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Breaker 1.5 Amp Protects the unit from drawing too much current. If tripped, controller is inoperative.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Control Module 347002K - See Also RBTRA19768 Controls the functions of the unit with input from the user via keypad (keypad included). NOTE: Units with serial # 10000 and greater.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Low Side Gauge - Generic Used to monitor the suction pressure of the vehicle being serviced. 1/8" female pipe connection back tap. -30hg-0 To 0-125 PSI Range, 350 PSI Retard, PSI, Kpa, Bar Pressure Scales On Face. Includes Mounting Hardware, Loctite sealant, Instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge - Generic Used to monitor the discharge pressure of the vehicle being serviced. 1/8" female pipe connection back tap. 0-500 PSI Range, PSI, Kpa, Bar Pressure Scales On Face. Includes Mounting Hardware and Instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Universal Air Purge Device R-12 Used to purge excessive air from refrigerant tank during vacuum or recycle process.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve Heavy-Duty Update Kit A two port valve, that normally allows fluid (liquid or gas) to flow through it in only one direction.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Keypad 347002K & 348002K - Control Module Style User input device attached to a circuit board to select start, stop, and program functions of the unit. Applies to units with serial numbers 10,000 & higher on 347002K or 30,000 & higher on 348002K. Please verify correct application of unit before purchasing any electrical component. (Newer units have 4 screws holding the Control module in place. Older units can be identified by having only 3 screws holding the Keypad bezel in place).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Panel Mount Valve Assembly 347002K & 348002K Allows user to control the flow from the vehicle into the recovery unit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Install Kit 7002K Unit To Use Cubigel Compressor
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Cubigel Compressor (Replaces The RA17110, RA17434, RA19458, & RA19748) Includes all hardware and electrical for a complete install. See additional plumbing retrofit kits noted for older style units.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve Kit (Block Style Units) Prevents incoming refrigerant from opening the charge solenoid and entering the liquid side of the ISV.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Repair kit with Oil Injector Caps (20) and bulkhead fitting (10) Used to attach the oil injector bottle to the unit, allowing user to inject oil into vehicle being serviced. See 523148
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fastener Seal and hardware kit for Robinair recovery units is a service provider must have. This kit contains 38 of the most requested hardware and small maintenance items on most Robinair machines many of which are difficult or impossible to find by themselves, including gaskets seals, bolts and screws, pneumatic fittings, door latches, Torx screws, flare gaskets and other hard to find or specific related items. 3/8 Hose Gasket, 1/4 Fl Copper gasket, O'Rings, Screws Torx, Speed Nuts, Tinnerman U Clip, 1/2 Acme Jam nut, Pneumatic Fittings, Pan Head screws, Grommets, Door Latch Receptacle, Connector, Plastite connector, Bezel 7002K / 700Z, Door Latch Spring, Injector Bulkhead Fitting, Oil Injector Cap And Bulkhead Fitting, Vacuum Pump Fill Caps, Shreader Cores. Housed in a Double sided flip top case with extra space for other items.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Ferrule & Nut 1/8" (Sold Each)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.