Automotive tools & equipment

HVAC & Industrial supplies

Sales - parts -service


  Home > Multimeters & Test Instruments >

100 TPI One Button Easy-Operation DMM With Protective Boot

100 TPI One Button Easy-Operation DMM With Protective Boot
 
Price $48.96


Product Code: TPI100
Qty:

Description Prop65
 

TPI 100 Easy One Button Operation Digital Multimeter with Protective Boot - The new TPI 100 automatically switches between AC and DC Voltage as well as resistance measurements. No more guessing what range to switch your meter to. The TPI 100 does it automatically. This multimeter features very ease one button operation automatically switches between AC Voltage, DC Voltage, and ohms (resistance) with a wide reporting range and a broad spectrum of uses.

Automatically switches between ACV, DCV, and ohms (resistance). Simple to use. Meter selects function and range, just connect the leads to the device under test.

Single button operation. Easy to use. Enables users with limited knowledge to perform tests safely.

0 to 600 volts AC and DC Enough range to safely perform measurements

10 MΩ internal impedance. High impedance prevents inaccurate reading caused by circuit loading.

Auto power off. Increases battery life by turning off the multimeter when not in use.

Product Features
  • EZ to use one button operation
  • Automatically Measures DC Volts, AC Volts and Ohms (Resistance)
  • Large 4,000 Count Display
  • 0 to 600 Volts AC and DC
  • 10M Ohm impedance
  • Auto Power Off After 10 Minutes
  • 4,000 count display
  • Up to 40MΩ
  • cULus 61010-1
  • CAT II - 1000V, CAT III - 600V
  • Includes Test Lead Set, Batteries and Protective Rubber Boot
  • 3 Year Limited Warranty

Model 100 Applications:

  • Measure line and control circuit voltages
  • Measure resistance of motor windings, transformers, and solenoids
  • Make general AC and DC voltage and resistance measurements
  • Measure the resistance of elements and electric heater cores
  • Test continuity of wiring
  • Verify voltage at breakers and outlets
  • Use as a back-up meter in your tool box

Category Ratings:

  • Category I: Usually electronic equipment or equipment where measures have been taken to limit transient over voltages.

  • Category II: Single phase loads like appliance personal computers, television sets, and other household loads. Outlets located more than 30 feet froma CAT III source or more than 60 feet from a CAT IV source.

  • Category III: Distribution level fixed installations like distribution panel devices, short branch and feeder circuits, three phase loads, and single phase commercial lighting.

  • Category IV: Equipment and lines located on the power line side of a service panel or where a low voltage connection is made to utility power

Model 100 Specifications
DC Volts Maximum Input: 600V (Minimum Input = 1.5V)

Maximum Resolution: 0.001V

Accuracy: +/-0.5%

AC Volts Maximum Input: 600V (Minimum Input = 1.7V)

Maximum Resolution: 0.1V

Accuracy: +/-0.8%

DC Amps N/A
AC Amps N/A
Resistance (Ohms) Maximum Input: 40MΩ

Maximum Resolution: 0.1Ω

Accuracy: +/-0.8%

Frequency N/A
Capacitance N/A
Inductance N/A
Temperature

(K-Type Thermocouple)

N/A
Continuity Audible at less than 100Ω
Diode N/A
Duty Cycle N/A
True RMS Responding No
Conductance No
Pulse Width No
Data Hold No
Min/Max Record No
Time Stamp Logging No
Relative Mode No
Compare Mode No
RS-232 Output No
Process Loop Output No
Sleep Mode / Auto Off No
Protective Boot Yes (standard)
Display Type 4000 count LCD
Range Selection Auto including function selection
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature 14°F to 122°F (-10°C to 50°C)
Humidity 80% non-condensing
Size 6” x 3.1” x 1.2” (187mm x 86mm x 33mm) with boot
Weight 12oz (340g) with boot
Battery Type 1.5V “AA” Alkaline (2)
Battery Life 500hrs Typical
OverInput Category CAT III 600V
Agency Approval IEC 61010-1
Warranty 3 Years


Browse for more products in the same category as this item:

Multimeters & Test Instruments
Multimeters & Test Instruments > Multimeters (DMMs)