 |
 |
 |
|
PL6800 Solar Pro-Logix 12 Volt 100/40/10 Amp Charger 100 Amp Flashing Power Supply provides stable power for vehicle reflashing applications, with up to 100 amps available on demand. This mode supports OE stable power supply requirements and allows operator control of target system voltage, from 13-14.9 Volts in 0.1V increments. Using a switching power supply and advanced circuitry, the PL6100 keeps voltage ripple to a minimum to deliver clean power that will not disrupt the reprogramming event. It also features fast load responsiveness to minimize voltage drop when system demand spikes.
The PL6800 features extra-long 13’ cable leads, enabling it to reach the starting points of any vehicle, our PowerJawTMclamps with angled jaws for improved access in tight engine compartments and a small footprint for compact installation within a diagnostic work station. Its leads are detachable via welding connectors, allowing easy field replacement in the event of damage. The unit features a 1-Year Limited Warranty and is repairable via our North American Service Network.
In power supply mode, the PRO-LOGIX PL6800 provides power to maintain vehicle electrical system voltage at a preset level, increasing its output in response to system load increases to maintain a stable power environment for successfully reprogramming. It features a voltage output range of 13.1-14.9V, adjustable in 0.1V increments. allowing the operator to dial the output in exactly as specified by the supplier of the vehicle under service. It features fast load responsiveness for ultra-quick recovery from system demand increases. It also delivers its massive power with minimal voltage ripple, providing a clean flow of power to the vehicle without risk of programming interference.
In charging mode, the PL6800 utilizes advanced microprocessor-controlled logic to precisely deliver a fully automatic charging routine designed to optimally charge and maintain each battery or battery pack serviced. The PL6800 features the ability to properly charge a wide variety of lead acid battery types, including Conventional, AGM, Spiral Wound, Start-Stop, Deep Cycle and Marine batteries – for virtually any lead acid battery type installed in a vehicle, the PL6800 can deliver a proper, beneficial charge.
In charging mode, the PL6800 adapts its approach based on the needs of each battery or battery pack it services. Such adaptations can include activating a soft start mode on deeply discharged batteries, a battery repair mode on older/distressed batteries and temperature compensation when charging in extreme temperatures. It also incorporates numerous features to make charging safer for the operator and the vehicle/battery being charged, including over-voltage protection, reverse polarity protection, smart clamp technology and battery fault detection.
Charge Multiple Battery Types
Traditional battery chargers utilize basic charging controls that make them appropriate for charging only Conventional and Maintenance Free Flooded (wet) Cell batteries. Use of traditional battery chargers on AGM or other modern batteries results in suboptimal charging and potential harm to the battery being charged.
PRO-LOGIX Charger models utilize advanced charging technology to deliver precise charge controls, enabling them to properly charge a wide variety of battery types.
Soft Start Mode and Battery Repair Mode
PRO-LOGIX Charger models utilize a proprietary advanced Multi-Phase charging process designed to optimally charge many types of batteries. One critical aspect of this proprietary process is the precise control achieved through the charging process, enabling the charger to monitor a battery’s specific reaction to the power supplied. The PRO-LOGIX charging process includes a Soft Start Mode to properly charge deeply discharged batteries and ensure that the energy from the charger is being properly incorporated into the battery. It also includes a Battery Repair Mode to attempt to restore batteries that do not properly accept charging current. The display will indicate BATTERY REPAIR by flashing the CHARGING LED and and monitor current acceptance by the battery. Battery charging time will be extended to allow the battery to recover. Both processes are fully automatic and require no intervention on the part of the operator, either to initiate the process or complete it.
Pre-Charge Battery Activation
Some modern batteries can cause charging problems if they have been deeply discharged. The plates in these batteries can begin sulfating quickly, forming a barrier to accepting a charge. This condition will be indicated by an extremely low (or zero) ammeter reading, indicating that the battery is not accepting current from the charger. A deeply discharged battery such as this may take as long as 4 to 8 hours before it will accept a charge. The Automatic Charging mode attempts to detect batteries with this condition (see Battery Repair Mode in PREPARATION) and automatically adjusts for it.
Designed to provide continuous battery charging operation in a wide variety of professional/industrial battery service environments. It combines fully automatic operation, utilizing a proprietary multi-phase charging process, with the ability to properly charge multiple battery types. Advanced charging logic, robust components, quick set-up and smart display feedback mean effective and efficient charging for your operation.
Model PL6800 features a compact footprint that is ideal for installation on a benchtop or mobile cart. It features removable cables, including output cables that utilize welding cable connectors for a secure fit, for ease of use and convenient replacement should a cable be damaged.
 Warning: This product may expose you to chemicals including lead which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Product Features
- 12 Volt operation
- Automatic charging mode for easy operation
- 100A max charge for fast charging of batteries to Group 31
- Properly charges a variety of lead acid battery types
- Power supply mode to support programming
- Precise voltage control and quick response to load
- Extra long 13’ cables reach all vehicle starting points
- Ability to manage depleted and sulfated batteries
- (Requires 20 Amp A/C Outlet)
Specifications
Model Number: PL6800
Operating Voltage: 12 Volt DC
Charging Rate: 100/40/10 Amp
Power Supply Max Output: 100 Amp
Warranty: 1 Year
|
|
|
|
|
|
|