100122 PROMAX Provax Black Knob

100123 PROMAX Provax Blue Knob

100124 PROMAX Provax Red Knob

Inlet Block Manifold shim plate installs directly over the manifold, preventing the valve stems from backing out after installation in the unit. This plate also prevents unwanted removal or accedental removal or service of stems during use. If you are replacing the manifold on your unit we strongly suggest installing this as well for safety reasons.

1/4" Flare Filter for ProMax and MiniMax Units Designed to protect recovery systems from debris and deposits that would normally harm your unit. Large filter capacity provides long life. All steel construction with enamel finish resists corrosion and rusting.

100345 PROMAX Hose, Blue, 4" Long

50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

518638 Robinair 15 Amp Magnetic Circuit Breaker provides protection of main electrical input. Single Pole 15 Amps 125-250 AC. Mounts Via Snap In Bezel. Terminal Connection 0.250 Spade terminals.

659904 PROMAX Complete Case Assembly (Rg5000 & Rg5410hp)

Inlet Block / Manifold Assembly includes black machined block, valves and old style flat knobs. (Caution! Do turn knobs from there original position before installing or they will lose there indexing and improper flow will result).

Inlet Block / Manifold Assembly includes black machined block, valves and new knobs. (Caution! Do turn knobs from there original position before installing or they will lose there indexing and improper flow will result)

CD1201 PROMAX Condenser

CP1001 PROMAX Compressor Mount (Rg5xxx)

CP1304 PROMAX Piston

Offset Motor Pump Coupler. Includes coupling, set screw, cap screws, dowel pin.

CP1320 PROMAX Compressor (Replaces CP1300 Except RG3305)

CP1321 PROMAX Connecting Rod (CP1320) less any hardware, you will need bearings, piston, screw, bushings and wrist pin to complete the assembly.

CP1322 PROMAX Crank Shaft (CP1320)

CP1392 PROMAX Piston Cylinder

Valve Plate, no valves or springs. When purchasing this it is customary to purchase the rebuild kit as well, found here.

CRXTOSP1 Tank Overfill Protection Cable Shorting Plug allows the user to override the tank float safety device on most recovery units using a 3 pin brad Harrison cable. Screws in place at the cable end allowing the unit to start. (Always use a scale for accuracy when using this device) 30 & 50 pound tanks should never be filled to a level beyond 80% of tank capacity.

DC0501 PROMAX Rg5000 Id Decal

DC0502 PROMAX Rg5000/5410hp Instruction Decal

EL1309 PROMAX Momentary Switch

EL1310 PROMAX On/Off Switch

EL1412 PROMAX Capacitor

EL1500 PROMAX Relay DPDT 120VAC 30A

Axial Fan 115 volt, .43 amp 35 watt Rotary Fan, 6.375" Mounting Hole Centers. Two wire lead set for power connection 14" & 24"with 1/4" spade terminals.

1/2 Hp Ac Motor (110v) with starting relay (not available as a seperate item)

FL1201 Promax Filter Drier

FLCK-1 PROMAX Filter Conversion Kit (Replaces MF1275 Swivel). Allows for use of common Filter Drier. Includes: 100343 Filter Drier, 100345 Blue 4" Hose, Flare Adapter Fitting, 1/4 seal cap with retaining strap.

350psi Gauge (Blue), 1/8" MPT Bottom Tap Fitting, -30"HG To 120 PSI 350 PSI Max Compound Scale, PSI/BAR pressure readings, R-12 / R-22 PT Scales

500psi Gauge (Red), 1/8" MPT Bottom Tap Fitting, 0 To 500 PSI 500 PSI Max Pressure Scale, PSI/BAR pressure readings, R-410a PT Scale

800psi Gauge (Red), 1/8" MPT Bottom Tap Fitting, 0 To 800 PSI 800 PSI Max Pressure Scale, PSI/BAR pressure readings, R-410a PT Scale

GA1000 PROMAX Gauge Lens

500psi Gauge (Blue), 1/8" MPT Bottom Tap Fitting, -30"HG To 250 PSI 500 PSI Max Compound Scale, PSI/BAR pressure readings, R-410a PT Scale

HA1090 PROMAX Ball Valve Handle (Black)

HA1091 PROMAX Ball Valve Handle (Blue)

HA1092 PROMAX Ball Valve Handle (Red)

This module plugs directly into the wire harness of your PROMAX Recovery unit through a plug already installed on your machine. This allows you to recover unattended with out the danger of tank overfill or the need to have a scale present to weigh the tank.

This PROMAX piston seal replacement kit is to be used on the old style (round cylinder) and new style (rectangle Cylinder) compressors on RG54xx series, MiniMax Series and PROVAC Compressors.

PROMAX Valve Replacement Kit is to be used on the old style (round cylinder) and new style (rectangle Cylinder) compressors on RG5410 series, MiniMax Series and PROVAC Compressors. Kit includes all necessary parts to rebuild damaged valves and seals.

This PROMAX piston compressor rebuild kit includes all parts needed to rebuild the new style (Rectangle Cylinder Only) compressors on RG54XX series, MiniMax Series and PROVAC Compressors. Kit includes all necessary parts to rebuild the piston "SLYD" Rings, Square piston seal and cylinder seat seals, as well as all necessary parts to rebuild damaged valves and seals and finally the bearings and shaft seal. This Kit does not include the actual valve plate, we suggest the purchase of the valve plate itself here. This kit will not repair round cylinder compressors.

Shaft Seal Replacement Kit for CP1320 Compressor. Includes bearings, seals and o-rings and illustrated instructions.

NB1102 PROMAX #4-40 Pan Head Cap Screw For Knobs

NB4205 PROMAX Connecting Rod Set Screw

PROMAX WRIST PIN 1/4" DIA X 3/4" For Connecting Rod (CP1320)

Rubber Foot, Steel impregnated washer for durability.

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

NB7005 PROMAX 10-24 Steel Rivnut

Designed for EXtremely Fast recovery of medium and high-pressure refrigerants, including R-410A (Puron). Features include automatic 13" Low Pressure Shut off (selectable for deeper recovery), automatic high pressure cut-out switch (selectable for low or high pressure gasses), for safety and a 20% increase in flow over the RG5410A. Direct liquid recovery without damaging the compressor and an Oil-less compressor which allows for rapid transfer of large amounts of liquid.

Having a hard time keeping up with work flow in a salvage yard or appliance recycling center? Recovering refrigerant can be time consuming and difficult to manage. This exclusive package from Century allows for the recovery of refrigerant from up to 10 appliances at one time making salvage operations quick and easy.  Our package solution offers you the ability to recover 100 or more appliances a day making your work easy and profitable. Our trained staff can even custom build one for you tailored to specific needs.

Discontinued SB1001 PROMAX 1.25" Needle Bearing for older style compressors

SB1009 PROMAX Crank Shaft Bearing

SB20086 PROMAX 2-006 Neoprene "O" Ring

SB2008 PROMAX 2-008 Neoprene "O" Ring

SB2013 PROMAX 2-013 Neoprene "O" Ring

SB2026 PROMAX 2-026 Neoprene "O" Ring

SB2027 PROMAX 2-027 Neoprene "O" Ring

SB2038 PROMAX 2-038 Neoprene "O" Ring

SB4000 PROMAX Connecting Rod Bronze Bushing 1/4" ID

SH5022 PROMAX Fan Screen

WR2002 PROMAX Power Cord (110v)