Internal Charger for older JNC660, JNC4000, JNC400 Manual charge units.

Red / Black Cable & Clamp Kit (JNC400 JNC4000) Red / Black Cables & Clamps, 4 GA Heavy Duty Cables, 46" Long For Easy Access.

Cable & Clamp 23 in. 4 AWG 400 Amp Positive

Cable & Clamp 23 in. 4 AWG 400 Amp Negative

Red / Black Cables & Clamps, 2 GA Heavy Duty Cables, 23" Long For Easy Access. Copper Jaws.

246-004-666 Switch Voltage Status JNC Push Button. Old Style (Small Diameter Hole) JNC Units. If your unit has the newer style switch with a 2 pin plug see 246-534-666.

246-417-666 Cigarette Lighter Socket With Cap

Switch Status Push Button with wiring

Switch Status Push Button with wiring

246-534-666 Switch Voltage Status JNC Push Button Kit (New Style). Includes all necessary wiring for both older wiring options with large hole. For JNC950 & JNC1224 Only. If your unit has the older style switch with ring terminals only see 246-004-666.

Voltmeter Round Panel Mount 11-15 Volt DC Threaded Post Terminal Connections. There are two versions of this meter, older units have spade connections and newer units have threaded wire terminals.

Voltmeter Round Panel Mount 11-15 Volt DC 1/4". Includes Quick disconnect Terminal Connections for older units. There are two versions of this meter, some units have spade connections and other units have ring terminals.

KK310310 Voltmeter Round  - DISC SEE 247-152-666

Clamp Cover For Jumper Cable Clamps. Prevents shorting during transportation and protects clamps from damage.

Internal Charger PC board Assembly with LED's for New Style Automatic Charging models and upgrade* to older units. Includes power supply, mounting bracket, circuit board, Charging status decal.
*Some modification to your older unit may be necessary to fit the new LED display.

ESA1 12 Volt extension cord Male cigarette lighter x Male cigarette lighter 48" adapter. Accessory used with many of our portable power sources including Booster PAC, Jump-N-Carry and Truck PAC. The cord can be used for charging the jump pac after use, or for a quick charge of a vehicle from inside the drivers compartment out of the elements.

Clore Automotive introduces the SOLAR ESA30 OBD II Memory Saver Connector, a memory saver connector that can be used in conjunction with a jump starter to preserve vehicle codes and electronic presets while a vehicle’s battery is disconnected. The ESA30 can be used on any jump starter with a 12 Volt power port. The ESA30 acts as an interface connector between a jump starter and a vehicle’s OBD II port. This prevents any electronic memory loss when disconnecting a vehicle’s battery. A proper connection is confirmed by the ESA30’s built-in LED light.

ESA5 12 Volt extension cord Male cigarette lighter x Male cigarette lighter 15' adapter. Accessory used with many of our portable power sources including Booster PAC, Jump-N-Carry and Truck PAC. The cord can be used for charging the jump-pac after use, or for a quick charge of a vehicle from inside the drivers compartment out of the elements. We also have one in a 6ft. length here.

JNC100 Clore Proformer 17aH Battery JNC400 & JNC4000

Clore Proformer Replacement Battery delivers 1700 Peak Amps of starting power and weighs only 18 lbs. If purchasing for a JNC770 you may need a 079-770-666 Buss Bar.

An entry-level professional unit, the JNC4000 combines power and ease-of-use in a durable, reliable unit. With a built-in charger

PP15 CHARGE IT! 15000 mAHr Lithium Micro Jump Starter - The CHARGE IT! Model PP15 15000 mAh POWER PAC is a lithium-battery based multi-voltage power supply and 12 Volt jump starter. With 15000 mAh of reserve capacity and multiple output voltages, the POWER PAC PP15 can power a wide variety of devices, electronics and accessories. In addition, the PP15 can be used to jump start vehicles from motorsports equipment, personal watercraft and ATVs to cars, trucks and SUVs. Delivering 400 Peak Amps and 270 Cranking Amps of starting power, it is powerful enough to start most 4- and 6-cylinder passenger vehicles.