Valve Core Remover / Installer Deep Core R-134A

Maximize your time and effort with our Multiport Recovery Inlet Manifold. Designed specifically for salvage operations and recycling centers, this manifold connects to the inlet of your recovery unit or manifold gauges and allows you to pull up to 11 appliances at a time. Constructed with full flow ports and no valve cores installed to restrict refrigerant flow (included if needed). The 1/4 flare ports are protected with brass seal caps. If you are using a manifold set on the inlet of your recovery unit put one of these on each red and blue hose and double your capacity. You can even daisy chain them together for additional capacity. (Don't forget extra hoses and piercing pliers when purchasing these).

This kit provides the fastest and easiest means of connecting charging lines to process tubes for evacuation and recharging a system. The design assures an absolute seal between tubing and the charging hose. It eliminates the need for flaring and the possibility of tubing chips getting into the system.

Access Valve Core Remover With 6 Valve Cores

Provides a means of checking refrigerant temperature in the stream of gas. The most accurate method of testing gas temp is by sampling the liquid directly.

Thread Chaser For Use 18560 & 18561 Access Valve Core Remover / Installer. For use with No. 18560 or 18561, value core remover / installer. This thread chaser actually repairs damaged threads on valve cores in the service line, without releasing refrigerant into the atmosphere.

For use with No. 18560 or 18561, value core remover / installer. this extractor lets you remove damaged cores in the service line while the system is fully charged, without releasing refrigerant into the atmosphere.

18080 Robinair 1/4" Compact Thumbscrew Core Depressor attach to standard 1/4" flare hose ends and allow the technician to control flow of gas by screwing in the depressor, it also allows the core to be "shut off" before removing the hose preventing finger burn.

Remove valve cores without losing the system charge. Designed specifically for use during evacuation or recharging of any system with valve core-type access ports. Makes replacing leaking valve core under charge a snap. Never recover a system to replace a core again. A huge time saver.

Remove and install the valve core from a 1/4" male flare access fitting without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of vacuum and charging.

Remove and install the valve core from a 1/4" male flare access fitting without the loss of refrigerant. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve.

Standard Valve Core: These are standard air conditioning system service port valve cores.

GM High Flow Valve Core: These are GM High Flow air conditioning system service port valve cores.

JRA Valve Core: These are JRA High Flow air conditioning system service port valve cores.

Volvo Valve Core: These are Volvo air conditioning system service port valve cores.

R134a - 8mm - LS Valve Core: These are 8mm Low Side air conditioning system service port valve cores.

R134a - 10mm - HS Valve Core: These are 10mm High Side air conditioning system service port valve cores.

This kit contains 5 Different valve cores for R-12 & R-134a for Standard and Large Valves, as well as Valve core tools for Standard and Large Valve Cores.

Valve Core Assortment. Contains Standard R12 & R134a Valve Cores, Late Model GM High Flow Valve Cores, Volvo Valve Cores, R12 & R134a Valve Core-8mm, R-12 &134a Valve Core-10mm High Side.

Master Valve Core & Cap Assortment: This kit provides you with 18 different part numbers for a total of 88 pieces fitting domestic and import air conditioning systems service ports.

: This assortment of replacement service port caps has two each of six part numbers.

Large Bore Valve Core Remover Tool: This item allows you to remove and install the Large Bore valve cores in late model vehicles.

Valve Core Remover Tool - Small: This item allows you to remove and install Standard valve cores.

Master Valve Core Remover/Installer. Universal R-12 134A Valve Core Removal Tool Set. Remove valve cores without losing the system charge. Designed specifically for use during evacuation or recharging of any system with valve core-type access ports. Makes replacing leaking valve core under charge a snap. Never recover a system to replace a core again. A huge time saver. This tool pays for it self the first time you use it. The tool removes standard R-12 cores as well as most R-134a cores on both Low & High Side Ports. Heavy brass construction with a fine chrome finish prevents corrosion and keeps the tool looking nice as well as easy to clean.

360-80359-00 RTI Replacement R-12 Hose Gaskets and Core Depressor Kit

These depressors fit behind and protrude through the hose gasket on 1/4" flare and 1/2 ACME standard fittings. If you are replacing hose gaskets it's a good idea to replace these as well.

The installation torque for standard cores 2 – 5 in. lbs. [0.23 – 0.56 Nm]. Breakaway torque is not an accurate way to verify the installation torque due to material, lubricants and other conditions that may exist.

43150 Robinair –58° To 302° F In-Stream Superheat Thermometer / Valve Core Removal Tool Provides a means of checking refrigerant temperature in the stream of gas. The most accurate method of testing gas temp is by sampling the refrigerant directly. Connects directly to a standard 1/4" flare access fitting. Remove, test and install the valve core from a 1/4" male flare access fitting without the loss of refrigerant, fast accurate measurements ensure to the degree temperature measurements for superheat or subcooling. A must have tool for the serious refrigeration engineer.

Remove valve cores without losing the system charge. Designed specifically for use during evacuation or recharging of any system with valve core-type access ports. Makes replacing leaking valve core under charge a snap. Never recover a system to replace a core again. A huge time saver. This tool pays for it self the first time you use it. The tool removes standard R-12 cores as well as most R-134a cores on both Low & High Side Ports. Heavy brass construction with a fine chrome finish prevents corrosion and keeps the tool looking nice as well as easy to clean.

The 60667 Yellow Jacket Refrigerant Recovery Pliers are the fastest and easiest way to evacuate refrigerant before disposal of a unit. Snaps onto refrigerant line and punctures large hole for immediate and maximum full flow to recovery unit. One adjustable tool fits all sizes from 3/16" to 7/8" O. D. hard tubing. Replaceable hardened steel needle and spare gaskets are available.

Replacement Needle & Gasket

1/4" SAE Cap with strap: Repair item for the 6900 series of vacuum pumps.

Maximize your time and effort with our Multiport Recovery Inlet Manifold. Designed specifically for salvage operations and recycling centers, this manifold connects to the inlet of your recovery unit or manifold gauges and allows you to pull up to 6 appliances at a time. Constructed with full flow ports and no valve cores installed to restrict refrigerant flow (included if needed). The 1/4 flare ports are protected with brass seal caps. If you are using a manifold set on the inlet of your recovery unit put one of these on each red and blue hose and double your capacity. You can even daisy chain them together for additional capacity. (Don't forget extra hoses and piercing pliers when purchasing these).

The Mastercool 70088 1/4" Tube Piercing Pliers snaps onto refrigerant line and punctures large hole for immediate and maximum full flow to recovery unit. One adjustable tool fits all sizes from 1/4" to 5/8" O.D. hard tubing. Replaceable hardened steel needle and spare gaskets are available.

Replacement Tip With Cap And Allen Screw For 70088

R134A Universal Large Bore Valve Core Remover

R134A Valve Core Remover And Installer. For small core fittings. R-134a Valve Core Remover Installer built with Ball valve design, No need to pump down a system for a simple core change. Controls refrigerant flow with 1/4 turn of the valve lever. Lever position also gives visual indication of whether valve is opened or closed. Solid brass construction High and low side fitting included.

Universal Valve Core Tool

Five pack of 1/4'' SAE plastic core removers.

A31999 1/4" Valve Core: 1/4" valve cores PTFE / neoprene seal replacement valve core rated at a maximum of 800 psi and 220°F (104°C).

A31999-100 1/4" Valve Core: 1/4" valve cores PTFE / neoprene seal replacement valve core rated at a maximum of 800 psi and 220°F (104°C).

A31999-25 1/4" Valve Core: 1/4" valve cores PTFE / neoprene seal replacement valve core rated at a maximum of 800 psi and 220°F (104°C).

A32004 1/4" Valve Core Tool

1/4'' valve core torque tool made in the USA. Sets the proper torque every time! Calibrated to precise torquing requirements for core valves, the tool will no longer tighten once proper torque is achieved. Eliminates guesswork which results in under or over torquing of cores

A32008-B JB Industries Valve Core Torque Tool Bulk (12 Pack)

Evacuation and recovery valve core remover tool. Plier type with a quick release trigger which punctures large holes into the line for discharge of a recovery unit. Fits 3/16'' to 7/8'' OD hard tubing.

Replacement hardened steel needle and gasket for A32100 evacuation and recovery tool.

1/4'' valve core remover tool by JB (A32500N). Specifically designed to valve off the system to remove valve cores. Features a quarter turn ball valve shut-off fitting and o-ring seals the valve core can be completely removed and replaced without losing system charge. Speed up evacuation, recovery, or recharging time through the full flow port. Storage area houses spare valve cores. Made in the USA.

Replacement core remover bit for A32500N.

Replacement Core Remover for A32525N and A32504

5/16'' valve core remover by JB (A32505N). Specifically designed to valve off the system to remove valve cores. Features a quarter turn ball valve shut-off fitting and o-ring seals the valve core can be completely removed and replaced without losing system charge. Speed up evacuation, recovery, or recharging time through the full flow port. Storage area houses spare valve cores. Made in the USA.

1/4'' valve core remover with access port made in the USA. Specifically designed to valve off the system to remove valve cores, this core remover has the access port. Features a quarter turn ball valve shut-off fitting and o-ring seals the valve core can be completely removed and replaced without losing system charge.

5/16'' valve core remover with access port made in the USA. Specifically designed to valve off the system to remove valve cores, this core remover has the access port. Features a quarter turn ball valve shut-off fitting and o-ring seals the valve core can be completely removed and replaced without losing system charge.

A32535N JB Industries 5/16" Core Removal Tool

AVC134C CPS 1/2" ACME Brass Cap With Chain Tether (2 Pack)

The CoreMax system eliminates process tubes and Schrader valves replacing them with a removable high flow valve. For units with process tubes and Schrader valves you may be able to reduce the cost of your refrigeration unit by replacing them with CoreMax. As a side benefit to eliminating process tubes, you may eliminate one or more brazed joints which are a potential leak path. This revolutionary method gives you the choice of how you want to test, fill and evacuate your systems. Sleeve actuated Design which allows removal and replacement of COREMAX valve core without loss of refrigerant in charged units.

CM-S250 JB Industries Core Max 1/4 Seat  - Tube/stub - 3 Pack

CM-S370 JB Industries Core Max 3/8 Seat  - Tube/stub - 3 Pack

CM-SNAP JB Industries SnapMate High Flow Service Quick Connector For CoreMax Valve Cores. The SnapMate service connectors are designed to provide quick connections to CoreMax Valve Cores as well as standard access valves. The Collets grip on the threads and are specifically designed for the Service Industry by providing quick and easy connections to all 7/16-20 (1/4" SAE 45º Flare) access valves.

CM-SS250 JB Industries Core Max 1/4 Seat/Saddle NIP - 3 Pack

CM-SS370 JB Industries Core Max 3/8 Seat/Saddle NIP - 3 Pack

CM-TRQ JB Industries Core Max Torque Wrench. The CoreMax Torque Wrench is used to properly install and torque the JB CoreMax valve into the CoreMax seat. The wrench is preset to 8 ft/lbs. of torque.

CM-VC003 JB Industries CoreMax High Flow Valve Core With Caps (3 Pack). The CoreMax system eliminates process tubes and Schrader valves replacing them with a removable high flow valve. For units with process tubes and Schrader valves you may be able to reduce the cost of your refrigeration unit by replacing them with CoreMax.  As a side benefit to eliminating process tubes, you may eliminate one or more brazed joints which are a potential leak path. This revolutionary method gives you the choice of how you want to test, fill and evacuate your systems. Sleeve actuated Design which allows removal and replacement of COREMAX valve core without loss of refrigerant in charged units.

CM-VC010 JB Industries CoreMax High Flow Valve Core With Caps (10 Pack). Imagine a System with No Process Tubes or Schrader Valves With no process tubes you have no online pinching and brazing improving quality and line throughput. The CoreMax system eliminates process tubes and Schrader valves replacing them with a removable high flow valve. For units with process tubes and Schrader valves you may be able to reduce the cost of your refrigeration unit by replacing them with CoreMax.

CM-VC025 JB Industries CoreMax High Flow Valve Core With Caps (25 Pack). Imagine a System with No Process Tubes or Schrader Valves With no process tubes you have no online pinching and brazing improving quality and line throughput. The CoreMax system eliminates process tubes and Schrader valves replacing them with a removable high flow valve. For units with process tubes and Schrader valves you may be able to reduce the cost of your refrigeration unit by replacing them with CoreMax.

CM-VC100 JB Industries Core Max Valve With Cap (100 Pack) Imagine a System with No Process Tubes or Schrader Valves With no process tubes you have no online pinching and brazing improving quality and line throughput. The CoreMax system eliminates process tubes and Schrader valves replacing them with a removable high flow valve. For units with process tubes and Schrader valves you may be able to reduce the cost of your refrigeration unit by replacing them with CoreMax.

One end is used for deflation, the other end to install or remove valve cores

This plier-type pinch-off tool temporarily closes off line while making repairs. The quick release trigger and rounded jaws prevent cutting while allowing for reopening and rounding using a standard flare bar. Great for accessing process tubes for charging and resealing, similar to factory seals found on small fractional systems.

Tube Piercing Pliers. Snaps onto refrigerant line and punctures large hole for immediate and maximum full flow to recovery unit. One adjustable tool fits all sizes from 3/16" to 7/8" O. D. hard tubing. Replaceable hardened steel needle and spare gaskets are available.

Replacement Tip For TLPP Tube Piercing Pliers

Remove and install the valve core from a 1/4" SAE male flare access fitting without the loss of refrigerant. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve. Designed for durability and long life.

Pocket Valve Core Tool w/ 4 Spare Cores

Dual Valve Core Tool (1/4" SAE Valves & Auto R-134a Valves)

TLVCS410 CPS Mini-Split 5/16" Female x 5/16" Male Valve Core Removal Tool. Remove and install the valve core from 5/16" Fittings. 1/4" Male flare access fittings on the side and top. Remove cores without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of recovery, vacuum and charging. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve. Designed for durability and long life. (This tools has 5/16" Male flare access fittings on the top).

TLVC410A CPS Mini-Split 5/16" Female x 1/4" Male Valve Core Removal Tool. Remove and install the valve core from 5/16" Fittings. 1/4" Male flare access fittings on the side and top. Remove cores without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of recovery, vacuum and charging. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve. Designed for durability and long life. (This tools has 1/4" Male flare access fittings on the top).

TLVC6 CPS JRA 6mm Valve Core Tool w/ 4 Spare Cores

Valve Core Tool R134A 8 MM And 10 MM Late Model. Those stubborn 8 mm and 10 mm valve cores on those late model vehicles don’t stand a chance with CPS' heavy-duty valve Core Tool. Knurled diameter body lets this tool get the job done.

Remove and install the valve core from a 1/4" SAE male flare access fitting without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of recovery, vacuum and charging. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve. Designed with a stainless steel ball and brazed side fitting for durability and long life. (This tool has 1/4 Flare fittings on all ports).

Remove and install the valve core from a 5/16" (1/2"-20) male UNF access fitting without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of recovery, vacuum and charging. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve. Designed for durability and long life. (All 3 fittings on this tool are 5/16")

Remove and install the valve core from 5/16" Fittings. 1/4" Male flare access fittings on the side and top. Remove cores without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of recovery, vacuum and charging. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve. Designed for durability and long life. (This tools has 1/4" Male flare access fittings on the side and top).

Rebuild kit for TLVC4 / TLVCS

Rebuild kit for TLVC410 / TLVCS410

This extractor lets you remove damaged cores in the service line while the system is fully charged, without releasing refrigerant into the atmosphere. For use with CPS TLVC410 and CPS TLVCS410.

This thread chaser actually repairs damaged threads on valve cores in the service line, without releasing refrigerant into the atmosphere. For use with CPS TLVC410 and CPS TLVCS410.

This core extractor lets you remove damaged cores in the service line while the system is fully charged without releasing refrigerant into the atmosphere. For use with CPS TLVC and CPS TLVCS.

Thread chaser for use with CPS TLVC and CPS TLVCS Access Valve Core Remover / Installer. This thread chaser actually repairs damaged threads on valve cores in the service line, without releasing refrigerant into the atmosphere.

Provides a means of checking refrigerant temperature in the stream of gas. The most accurate method of testing gas temp is by sampling the liquid directly. For use with CPS TLVC and CPS TLVCS.