Power Cord 115 Volt 3 Prong. Termination Specs 16/3 84", 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White) with Strain Relief. When Discontinued See 0090026136

0090026136 Schumacher Power Cord 115 Volt 3 Prong. Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White) with Strain Relief.

This Knob is for selector switches on SE Series chargers only, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

Mechanically controls charging in timed Mode with manual hold mode. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" spade terminals.

0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

This Knob is for selector switches with a 3/4 Shaft only, there are separate knobs for timers with a half shaft. Please check your part numbers carefully.

0499000051 Schumacher 6 Position Rotary Selector Switch With Knob (7 Terminals With Trace). Uses Newer "Twist Lock" Mounting System For newer units. If your unit has an older threaded shoulder with a Pal Nut, use the 0499000022 version of this switch.

1199003352 Schumacher Foot, Metal, no hardware included.

2100800011 Schumacher Pop Rivet 3/16" X 5/16" Long

2299001552 Schumacher Heatsink Rectifier Assembly

Fan Motor provides cooling for the unit. 80mm x 80mm x 25mm 12volt DC quite design keeps noise to a minimum. May require the purchase of a 2299001542 Schumacher 12volt DC Fan Speed Controller. Note plug end to determine correct fit. *Please note: You may have to swap plug ends from your old fan.

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Used on newer style units. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap.

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Used on newer style units. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap. *(fan speed control board sold separately)

12volt DC Fan Speed Controller (Two Wire New Style)

2299002762 Schumacher Fan Speed Control (Single Fan) For Rivit See 2100800011

3199100028A 75 Amp 400 Volt Positive Diode (Anode On Lead). Press in diode, used in a wide array of applications. Once installed in the heat-sink these may require soldering to install onto transformer taps.
Use caution when replacing diodes always verify polarity or damage to equipment or self may result. Century Tool & Equipment assumes no responsibility for loss, damage or personal injury due to the miss-application of any electrical component. Purchase of this item agrees to said statement. This item should only be installed by a qualified and experienced electrician.

Output Cable And Clamp, Black Negative, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 80" long with strain relief on cable.

Output Cable And Clamp, Red Positive, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 80" long with strain relief on cable.

3999000107 Schumacher Circuit Breaker 32 Volt DC 90 Amp. When ordering, it may be necessary to purchase a pair of the 5199000406 screws if replacing and older circuit breaker for retrofit.

Fan Motor provides cooling for the unit. 80mm x 80mm x 25mm 12volt DC Quiet design keeps noise to a minimum. May require the purchase of a 2299001542 Schumacher 12volt DC Fan Speed Controller. Note plug end to determine correct fit. *Please note: If replacing the 2299001565, you may have to swap plug ends from your old fan to make the new fan work. See 169116-001 for connectors

5100000005 Screw M3 X 5.5 For Original Timer

5199000406 Schumacher Screw 1/4-28 x 0.375 (Circuit Breaker Connection Screw)

Ammeter Horizontal 0-200 AMP features easy snap-in installation, no tools required. Red Green Charge Rate face. 0-40 Amp range For Charge 0-200 Amp Start. Wire through induction pick-up for greater accuracy.

6094K89 Knob For Battery Charger Selector Switches & Timers. This Knob is for selector switches and timers, designed with 1/4" ID and a set screw for locking onto shaft. Suitable for all 1/4" shaft switches. Replaces Schumacher 0099000045 & 0099000096.

TJ1-120MB Universal Mechanical 2 Hour Timer With Finish Bell. Mechanically controls charging in timed Mode, has "Hold" for manual un-timed charging. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" Quick Disconnect terminals. Includes mounting screws. Replaces many older mechanical timers.