This Knob is for selector switches on SE Series chargers only, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

0099000062 Schumacher 6" CW Fan Blade.

Fan Motor Open Frame 115 Volt

0099000080 Wheel 6" Plastic For 3/8 Axle

0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

0099000201 Axle Rod 3/8 X 14.25" Zinc Plated

6" Front foot for new style battery chargers

This Knob is for selector switches with a 3/4 Shaft only, there are separate knobs for timers with a half shaft. Please check your part numbers carefully.

4 Position Rotary Switch with hard wire push in connections. (Works with solid or stranded wire, see notes)

Axle End Cap Fits .375 (3/8") Diameter Axle, Sold as a Pair, Can be used on any 3/8" Axle to secure wheels.

Heatsink Rectifier Assembly 4 Diode design, requires soldering to install. Check your unit for size and type, there were several versions of this unit, earlier units are no longer available. Caution should be used when installing this product and care taken to insure over heating or shorting does not occur while soldering. This unit does not include insulators, bolts, nuts or any other hardware. Discontinued See 3199100028A 75 Amp 400 Volt Positive Diode (Set Of 4) individual diodes.

Battery Charger Wheels - Handle - Hardware Kit For SE3000, SE6030. Includes 3599000210 Handle, 0099000080 Wheels, 0099000123 Plastic Foot, 0099000066 Axle, 2299001076 Misc Parts Bag (screws etc..)

120 Minute mechanical timer with knob. 120 minute total time. Mechanically controls charging in timed Mode with manual hold mode. Single Pole Single Throw (SPST) Switch rated 15 amperes, finish bell.

Fan Blade 6" 4 Blade CW. Same as 130007-001 Christie

3199100028A 75 Amp 400 Volt Positive Diode (Anode On Lead). Press in diode, used in a wide array of applications. Once installed in the heat-sink these may require soldering to install onto transformer taps.
Use caution when replacing diodes always verify polarity or damage to equipment or self may result. Century Tool & Equipment assumes no responsibility for loss, damage or personal injury due to the miss-application of any electrical component. Purchase of this item agrees to said statement. This item should only be installed by a qualified and experienced electrician.

3599000302 Schumacher Battery Charger Handle Round Chrome Flat Side

Single Pole Thermal Type Breaker (Paired), Bracket Type Mounting for universal applications, 10-32 Studs for easy wire connections. 12 Volt 30 Amp Each. Sold unassembled, keep your original hardware and bus bars as these are sold individually with no hardware or nuts.

51-288 115 Volt Fan Motor With Fan Blade & Mount. .195 diameter shaft. Your unit may not require the mount, in which case discard it.

5100000005 Screw M3 X 5.5 For Original Timer

5399100117 Ammeter Horizontal 0-80 Amp Range with Charge & Start

Ammeter Horizontal 0-80 AMP features easy snap-in installation, no tools required. Yellow Orange Charge Rate face. 0-80 Amp range and wire through induction pick-up for greater accuracy.

6094K89 Knob For Battery Charger Selector Switches & Timers. This Knob is for selector switches and timers, designed with 1/4" ID and a set screw for locking onto shaft. Suitable for all 1/4" shaft switches. Replaces Schumacher 0099000045 & 0099000096.

TJ1-120MB Universal Mechanical 2 Hour Timer With Finish Bell. Mechanically controls charging in timed Mode, has "Hold" for manual un-timed charging. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" Quick Disconnect terminals. Includes mounting screws. Replaces many older mechanical timers.